Skip to lesson
PCPHYSICS CREST
1

Unit 5 · Torque and Rotational Dynamics

The Unit 5 idea
Rotation is not a new universe. It is the same physics viewed around an axis: displacement → angular displacement, velocity → angular velocity, force → torque, mass distribution → rotational inertia, and Newton's second law → $\sum\tau=I\alpha$. The AP difficulty is choosing the right axis, representation, and relationship.

5.1 · Rotational Kinematics

Rigid system
A rigid system keeps its shape while rotating, so different points may move in different directions. Because of that, the full rotating system cannot always be modeled as a single point object.
Angular displacement$\Delta\theta=\theta_f-\theta_i$
Average angular velocity$\omega_{avg}=\dfrac{\Delta\theta}{\Delta t}$
Average angular acceleration$\alpha_{avg}=\dfrac{\Delta\omega}{\Delta t}$
Sign convention
Choose clockwise or counterclockwise as positive and stay consistent. Current AP Physics 1 limits rotational-direction descriptions to clockwise/counterclockwise about a stated axis; you do not need a 3-D torque-direction rule.
PCCW +fixed axis; counterclockwise positive

Radians are the natural angular unit: $2\pi\,\mathrm{rad}=1$ revolution.

Every point on a rigid disk sweeps the same $\Delta\theta$ in the same interval, even though points farther from the axis travel farther.

Quick Check 1
A wheel turns through $-6\pi$ rad. If counterclockwise is positive, how many revolutions and in what sense?
$-6\pi/(2\pi)=-3$ revolutions: 3 clockwise revolutions.
2

Angular Motion Uses the Same Kinematics

Constant-$\alpha$ toolkit
For constant angular acceleration, use the same structure as Unit 1 kinematics:
$\omega_f=\omega_i+\alpha t$
$\Delta\theta=\omega_i t+\tfrac12\alpha t^2$
$\omega_f^2=\omega_i^2+2\alpha\Delta\theta$

Equation selection

List knowns and the target. Choose the relationship that avoids an unwanted unknown. Do not force a formula just because it looks familiar.

θ / rad02t / s04ω / (rad/s)02t / s04α / (rad/s²)02t / s02

Local slope of $\theta$–$t$ gives instantaneous $\omega$; a finite chord gives the average.

Local slope of $\omega$–$t$ gives instantaneous $\alpha$; a finite chord gives the average.

Area under $\omega$–$t$ gives $\Delta\theta$.

Angular speed vs angular velocity
A wheel can have positive angular velocity and negative angular acceleration: it is rotating in the positive sense while slowing down. Sign of $\alpha$ alone does not tell you whether the wheel is speeding up.
Quick Check 2
A wheel starts at $4\,\mathrm{rad/s}$ and has constant $\alpha=-2\,\mathrm{rad/s^2}$ for $3$ s. Find $\omega_f$.
$\omega_f=4+(-2)(3)=-2\,\mathrm{rad/s}$. It stops and reverses before 3 s.
3

5.2 · Connecting Linear and Rotational Motion

Signed arc displacement$\Delta s=r\Delta\theta$
Tangential speed$v_t=r|\omega|$
Signed tangential acceleration$a_t=r\alpha$
Same angular motion, different linear motion
Every point in a rigid rotating system has the same $\omega$ and $\alpha$, but points farther from the axis have larger arc-distance, tangential-speed, and tangential-acceleration magnitudes when the corresponding angular quantities are nonzero. Total angular distance accumulates the magnitudes of each traveled portion; net angular displacement can cancel when rotation reverses.
ABCCW +fixed axis; counterclockwise positive

If $r_B=2r_A$, then $v_B=2v_A$ and $a_{t,B}=2a_{t,A}$ for the same $\omega$ and $\alpha$.

Do not confuse tangential acceleration with centripetal acceleration. Unit 5's direct linear–rotational bridge is $a_t=r\alpha$.

Distance from the axis
For a point on a rotating sphere, the relevant $r$ is the perpendicular distance to the rotation axis—not automatically the sphere's radius. At latitude $\lambda$ on a spherical planet of radius $R$, that distance is $r=R\cos\lambda$.
Quick Check 3
Point B is three times farther from the rotation axis than point A on the same rigid disk. Compare their tangential speeds.
$v=r|\omega|$, so $v_B=3v_A$. Their angular speeds are equal.
4

5.3 · Torque: The Rotational Effect of a Force

  • Torque is a force’s turning effect about a chosen axis.
  • Angular acceleration depends on net torque and rotational inertia about that axis.
  • Mass distribution matters: equal masses can resist angular acceleration differently.
Torque magnitude
$$\tau=rF\sin\phi=rF_\perp=r_\perp F,$$ where $\phi$ is the angle between the position vector from the axis and the force. The lever arm $r_\perp$ is the perpendicular distance from the axis to the force's line of action.
pivotFr60°r⊥force direction and application point shown; schematic

Maximum torque for fixed $r$ and $F$: force perpendicular to $r$.

Zero torque: force applied at the axis, or its line of action passes through the axis.

Angle trap
Use the angle between $\vec r$ and $\vec F$. If a problem gives an angle $\beta$ from the perpendicular to the handle, then $\tau=rF\cos\beta$. Equivalently convert to the angle from the rod before using $\sin\phi$.
Current AP boundary
AP Physics 1 expects mathematical manipulation of torque magnitude and clockwise/counterclockwise rotational effects, but the 3-D vector direction of torque is beyond the course boundary.
Quick Check 4
A $20$ N force is applied $0.40$ m from a pivot at $30^\circ$ to the rod. Find the torque magnitude.
$\tau=rF\sin30^\circ=(0.40)(20)(0.5)=4.0\,\mathrm{N\,m}$.
The same tangential force acts at twice the radius. Its torque becomes…

5

Torque Technique: Draw Forces Where They Act

Force diagram ≠ ordinary FBD
A torque force diagram must show where each force acts relative to the axis. Two equal forces can produce different torques if their lever arms differ.

Reliable routine

  1. Mark the axis.
  2. Draw every real external force at its point of application.
  3. Decide which forces have zero lever arm.
  4. Compute each torque magnitude.
  5. Assign clockwise/counterclockwise signs consistently.

Functional dependence

For fixed angle, $\tau\propto rF$.

Double $F$ → double $\tau$.

Double $r$ → double $\tau$.

Move the line of action through the pivot → $\tau=0$.

CM / pivotrxleft actuatorright actuator2FFradial Freset horizontal before each trial; stated force data

The horizontal force whose line of action passes through the axis gives zero torque about that axis.

The pivot force itself gives zero torque about the pivot because its lever arm is zero.

Quick Check 5
A force is doubled while its lever arm is halved and the angle is unchanged. What happens to torque magnitude?
It is unchanged: $\tau\propto rF$, so $(r/2)(2F)=rF$.
6

5.4 · Rotational Inertia

  • Use the perpendicular lever arm or rF sin θ.
  • Forces through the axis produce zero torque.
  • Rotational inertia changes when mass moves relative to the axis, so identify both the object and axis in comparisons.
Rotational inertia
Rotational inertia $I$ measures resistance to angular acceleration about a specified axis. It depends on total mass and how that mass is distributed relative to the axis.
Point mass$I=mr^2$
Several point masses$I_{tot}=\sum_i m_i r_i^2$
Parallel-axis theorem$I'=I_{cm}+Md^2$
axism at rm at 3rpoint masses; light rigid support; stated axis

The outer equal mass contributes $m(3r)^2=9mr^2$: distance matters quadratically.

For a given rigid body in a plane, $I$ is minimum about a parallel axis through the center of mass.

What AP expects you to calculate
For collections of point-like objects, AP Physics 1 limits explicit $I=\sum mr^2$ calculations to five or fewer objects in a two-dimensional configuration. Formulas for extended rigid bodies are supplied when needed. You should still reason qualitatively about how shape and axis location affect $I$.
Axis is part of the answer
A rigid body does not have one universal rotational inertia. Change the axis and $I$ changes.
Quick Check 6
Two equal point masses are each moved from radius $r$ to $2r$ from the same axis. By what factor does the total rotational inertia change?
Each $mr^2$ term becomes $m(2r)^2=4mr^2$, so the total $I$ becomes 4 times as large.
7

5.5 · Rotational Equilibrium

Rotational equilibrium
$$\sum\tau=0\quad\Rightarrow\quad \alpha=0,$$ so angular velocity is constant. Constant angular velocity includes the special case $\omega=0$.
Two separate equilibrium tests
$\sum F=0$ controls translational acceleration. $\sum\tau=0$ controls angular acceleration. A system can satisfy one without satisfying the other. For a freely translating rigid body, use net torque about the CM to describe angular acceleration. For fixed-axis rotation, use torque and inertia about that fixed inertial axis. In static equilibrium, zero net force makes zero-torque balance independent of the calculation pivot.
hingebeam: M, LmMgmgsupporthinge forceillustrative M = m; force arrows share a scale

Choose the pivot strategically—often at an unknown support force—so that force contributes zero torque to the torque equation.

After using $\sum\tau=0$, use $\sum F=0$ if another support component is still unknown.

Pivot choice
The physical state does not depend on your chosen calculation pivot. A smart pivot simply removes inconvenient unknown torques.
Current AP boundary
Unit 5 analysis is confined to rotation in a single plane about a stated axis; AP Physics 1 does not require simultaneous rotational analysis in multiple planes.
Quick Check 7
A beam has $\sum F=0$ but a nonzero net clockwise torque. Is it in full equilibrium?
No. Its CM has no translational acceleration but it has angular acceleration about the CM because $\sum\tau\neq0$.
8

5.6 · Newton’s Second Law in Rotational Form

Linear$\sum F=ma$
Rotational$\sum\tau=I\alpha$
Bridge at radius $r$$a_t=r\alpha$
Full rotating systems often need two analyses
A hanging mass + massive pulley problem is not solved by torque alone. Write Newton's second law for the translating block, rotational Newton's second law for the pulley, then connect them with the no-slip relation $a=R\alpha$.
RmTmgT on pulleyaxle forceMglight string; no slip; fixed frictionless axle

For a light string, fixed central axle, negligible axle friction, and the descending sense positive, the block equation is $mg-T=ma$.

For the pulley: $TR=I\alpha$.

No slip: $a=R\alpha$.

If the block accelerates downward, $T<mg$; therefore the pulley torque is $TR$, not $mgR$.

This also explains an AP comparison trap: pulling the string directly with force $F$ gives torque $FR$, but hanging a block whose weight is $F$ gives a smaller pulley torque because its tension is less than its weight while it accelerates.

Quick Check 8
A disk has $I=0.80\,\mathrm{kg\,m^2}$ and net torque $2.4\,\mathrm{N\,m}$. Find $\alpha$.
$\alpha=\tau_{net}/I=2.4/0.80=3.0\,\mathrm{rad/s^2}$.
Your turn · Find angular acceleration for net torque 3.0 N m and rotational inertia 0.50 kg m².

Decimals, scientific notation and compatible units are accepted. Keep any required sign.

9

When Torque Changes, Angular Acceleration Changes

Angle-dependent torque
For a rigid bar pivoted at one end, gravity acts at the center of mass. If $\phi$ is measured from the horizontal, the gravitational torque magnitude is $Mgr_{cm}\cos\phi$. As the bar falls toward vertical, that torque decreases.
Mgφhorizontal lever armφ below horizontal; falling clockwise; schematic

$\alpha(\phi)=\tau_{net}(\phi)/I$.

While the bar is rotating downward and before any stop or reversal, a constant opposing friction torque $\tau_f$, a clockwise-positive model may look like $$\alpha(\phi)=\frac{Mgr_{cm}\cos\phi-\tau_f}{I}.$$

Constant torque is not constant angular speed
Constant nonzero net torque produces constant angular acceleration—not constant angular velocity.

Graph translation

Given $\alpha(t)$, the change in angular velocity is the signed area under the curve. Given $\omega(t)$, slope gives $\alpha$ and area gives $\Delta\theta$.

Quick Check 9
A wheel has constant $I$. Its net torque is halved. What happens to its angular acceleration?
$\alpha=\tau_{net}/I$, so $\alpha$ is halved.
10

AP Lab Thinking · Determine $I$ and Frictional Torque

Linearize rotational dynamics
For trials rotating in the same sense, if a tangential pull at lever arm $r$ produces applied torque $\tau_{app}=rF$ while axle friction provides an approximately constant opposing torque $\tau_f$, then $$rF=I\alpha+\tau_f.$$
0240159τapp / (N·m)α / (rad/s²)

Vary the applied force while keeping the lever arm fixed. Measure the angular acceleration for each trial.

Plot $\tau_{app}=rF$ vertically against $\alpha$ horizontally. The slope gives $I$ and the vertical intercept gives $\tau_f$.

Reduce uncertainty

Use several trials, a wide range of torque values, repeated timing/angle measurements, and a best-fit line rather than two points.

Alternative experiment

A falling yo-yo or hanging mass can also determine $I$ by combining $\sum F=ma$, $\sum\tau=I\alpha$, and $a=r\alpha$.

Quick Check 10
On a graph of applied torque versus angular acceleration, what physical quantity is the slope?
From $\tau_{app}=I\alpha+\tau_f$, the slope is $I$.
11

AP Transfer Routines

Mathematical Routines

Start from $\sum\tau=I\alpha$ or a constant-$\alpha$ kinematics relation, derive symbolically, then calculate.

Translation Between Representations

Move among force diagrams, $\alpha(t)$, $\omega(t)$, torque expressions, and physical motion.

Experimental Design & Analysis

State what you vary and measure, linearize the relationship, identify slope/intercept meaning, and reduce uncertainty.

Qualitative/Quantitative Translation

Make a claim first, derive a relationship second, then verify that the functional dependence supports the claim.

Functional-dependence routine
Before calculating, ask: what stays fixed? For $\alpha=\tau/I$, increasing lever arm can increase torque; moving mass outward can increase $I$. Those effects can compete. Never predict from one factor while ignoring another.
When two changes compete
Moving a point mass rigidly fixed to a pivoted bar between separate release trials can change both its gravitational torque (roughly proportional to lever arm) and the system rotational inertia (contains an $mr^2$ term). Therefore the change in $\alpha=\tau_{net}/I$ cannot be predicted from torque alone; compare both numerator and denominator.
Do not import Unit 6 early
Angular momentum, rotational kinetic energy, torque-work, and rolling-energy analysis belong to Unit 6. Unit 5 should be solved with rotational kinematics, torque, rotational inertia, equilibrium, and $\sum\tau=I\alpha$ unless the problem explicitly combines earlier linear concepts.
Quick Check 11
Same net torque acts on two rigid systems. System B has three times the rotational inertia of A. Compare angular accelerations.
$\alpha\propto1/I$, so $\alpha_B=\alpha_A/3$.
12

Unit 5 · AP Master Sheet

Average angular rates$\omega_{avg}=\Delta\theta/\Delta t$, $\alpha_{avg}=\Delta\omega/\Delta t$
Constant $\alpha$$\omega_f=\omega_i+\alpha t$
$\Delta\theta=\omega_i t+\tfrac12\alpha t^2$
$\omega_f^2=\omega_i^2+2\alpha\Delta\theta$
Linear bridge$\Delta s=r\Delta\theta$, $v=r|\omega|$, $a_t=r\alpha$
Torque$\tau=rF\sin\phi=r_\perp F$
Inertia$I=\sum mr^2$, $I'=I_{cm}+Md^2$
Dynamics$\sum\tau=I\alpha$
10-second AP checklist
  1. What is the axis?
  2. What rotational direction is positive?
  3. Where does each force act?
  4. Which forces have zero lever arm?
  5. Is $I$ about the same axis?
  6. Is the system in rotational equilibrium or accelerating?
  7. Do I also need $\sum F=ma$?
  8. Do I need $a=r\alpha$?
  9. Can I predict the change before calculating?
  10. Does my result match that prediction?
High-value traps
Trap 1: $\sum F=0$ does not guarantee $\sum\tau=0$. Trap 2: equal $\omega$ does not mean equal tangential speed. Trap 3: torque depends on perpendicular lever arm. Trap 4: rotational inertia depends on axis. Trap 5: a hanging block's tension is not automatically $mg$. Trap 6: torque vector direction is outside the AP1 boundary.
Quick Check 12
A rigid system rotates at constant nonzero angular velocity. What is its net torque?
$\alpha=0$, so $\sum\tau=I\alpha=0$.