Topic 1.5B · Forces B · Friction, Turning & Stability
Gravity in calculations: near Earth, g ≈ 9.8 m/s² (9.8 N/kg). Use the value supplied by the question, page instructions or activity; use 10 when it is specified.
Connect contact forces to real motion, then see every turning problem through one examiner lens: force, perpendicular distance, turning sense, and the line of action of weight.
Friction
Solid friction is a force between surfaces that may impede their relative motion. It acts along the contact surface and opposes actual or attempted sliding.
Useful friction
Shoe grip, tyre grip, brakes, holding an object, writing.
Unwanted friction
Wear and heating in bearings, axles and sliding machine parts.
Relative motion first · friction Opposes it · draw along the contact Material.
Set the relative sliding direction
Air and liquid resistance
Drag is the resistive force on an object moving relative to a liquid or gas. Air resistance is drag in air.
Direction
Opposite the motion relative to the fluid.
Speed effect
Drag usually increases as relative speed increases.
Shape effect
Streamlining usually reduces drag.
If weight exceeds drag, the resultant is downward. As speed rises, drag grows. When drag equals weight, the resultant and acceleration are zero, so the object continues at constant speed.
Compare weight and upward drag
Moments
- A moment measures turning effect about a pivot.
- Moment = force × perpendicular distance from pivot to the force’s line of action.
- Extend the force line if needed and draw the shortest distance to it.
The moment of a force is a measure of its turning effect about a pivot.
$d$ is the perpendicular distance from the pivot to the force’s line of action. Moment is measured in N m.
Worked moment
$M=(30)(0.40)=12$ N m clockwise.
Use the perpendicular lever arm
Force × Perpendicular distance · state turning Sense · include Unit N m.
Perpendicular distance
- A tilted beam’s length is not necessarily this distance.
- A force passing through the pivot has zero moment even if its application point is far away.
- A door handle gives a large lever arm, making a useful turning effect possible with a smaller force.
- Moments are expressed in N m; they are not described as energy in joules in this context.
- Extend the force arrow into a straight line of action.
- Locate the pivot.
- Draw the shortest line from pivot to line of action.
- Check for a right angle.
- Use that distance in $M=Fd$.
Worked angled force
Use 0.18 m: $M=(45)(0.18)=8.1$ N m. The 0.25 m sloping tool length is not perpendicular to the force line.
Force through pivot
Perpendicular distance is zero, so the moment is zero even if the force is large.
Force at 90° to lever
The lever length is then the perpendicular distance.
Same force, different perpendicular distance
Pause · explain it yourself
Why is it harder to open a door by pushing near the hinges?
Compare, then improve
The perpendicular distance is smaller, so the same force produces a smaller moment.
Check your physical idea, the conditions and any units. Edit your answer if a step is missing.
Principle of moments
- For rotational equilibrium, sum of clockwise moments equals sum of anticlockwise moments.
- Choose a pivot that removes unknown forces passing through it.
- List the direction of each moment before summing.
One force on each side
$(20)(0.30)=F(0.20)$, so $F=30$ N.
Several forces
Total anticlockwise moment $=(100)(1.5)+(60)(0.5)=180$ N m.
For balance, $F(1.0)=180$, so $F=180$ N.
One force on each side
Choose pivot · mark Anticlockwise/clockwise · use perpendicular Lever arms · Compare totals.
Equilibrium
- Include the beam’s weight unless it is negligible; for a uniform beam this acts at the midpoint.
- Full equilibrium also requires zero resultant force.
- A support force through the chosen pivot has no moment there but still enters the vertical force balance.
- Keeping these two conditions separate prevents an incomplete solution.
A rigid object is in equilibrium only when there is no resultant force and no resultant moment. One condition does not guarantee the other.
| Situation | Resultant force | Resultant moment | Consequence |
|---|---|---|---|
| complete equilibrium | zero | zero | no linear or angular acceleration |
| equal opposite forces on different lines | zero | may be non-zero | turning tendency |
| moments balance but forces do not | non-zero | zero | linear acceleration |
Quick check · A balanced beam is horizontal. Is that enough?
Pause · explain it yourself
What condition is needed in addition to zero resultant moment for full equilibrium?
Compare, then improve
Zero resultant force. For the beam example, support must balance total downward weight.
Check your physical idea, the conditions and any units. Edit your answer if a step is missing.
Centre of gravity
- To locate it in a thin irregular lamina, suspend the lamina and mark a vertical using a plumb line.
- Repeat from another hole; the lines intersect at the centre of gravity.
- When tilting an object, consider the vertical through this point.
The centre of gravity is the point through which the object’s entire weight may be considered to act.
- Make a small hole near the lamina edge.
- Suspend freely from a pin.
- Hang a plumb line from the same pin and wait until still.
- Trace the vertical line on the lamina.
- Repeat from a well-separated second hole.
- Mark the intersection; use a third line as a check.
Hole · Suspend · Plumb · Trace · Intersect · Check.
Pause · explain it yourself
Why use more than one suspension point for a lamina?
Compare, then improve
One plumb line locates only a line containing the centre. A second gives an intersection identifying the point.
Check your physical idea, the conditions and any units. Edit your answer if a step is missing.
Stability and toppling
- While the vertical line through the centre of gravity lies within the support base, weight can provide a restoring moment.
- Beyond the support edge, weight gives an overturning moment.
- A wider base and lower centre of gravity generally allow a greater tilt before toppling.
- Friction resists sliding but does not replace this geometric stability condition.
For a supported object, imagine a vertical line through its centre of gravity:
Inside base
Weight gives a restoring tendency about the nearest edge.
Through edge
The object is at the tipping threshold.
Outside base
Weight gives an overturning moment.
Simple rectangular model
Low centre of gravity · Wide base · weight line stays Inside.
ATP Lab Lens: moments, COG and stability
Moment practical
Horizontal beam, low-friction pivot, vertical forces, perpendicular distances, repeat arrangements.
COG practical
Small holes, free suspension, settled plumb line, thin traces, third-line check.
Stability practical
One factor changed, same base/mass controls, slow tilt, repeat threshold angle.
| Error source | Likely effect | Targeted improvement |
|---|---|---|
| pivot friction | beam can appear balanced when moments differ slightly | sharp low-friction pivot; gently disturb and let settle |
| parallax on positions | lever arm too high or low | read directly above/below hanger line |
| thick plumb traces | broad COG intersection | sharp pencil and thin line |
| toppling release too fast | threshold angle overshot | raise board slowly; use fine angle scale |
Topic 1.5B Master Sheet
Equation bank
Memory board
| If the question shows… | First move |
|---|---|
| object moving through fluid | draw drag opposite relative motion |
| pivot + force arrow | extend line of action and find perpendicular distance |
| several beam forces | calculate each $Fd$ and group CW/ACW |
| “equilibrium” | check both resultant force and resultant moment |
| suspended lamina | trace two or more plumb verticals |
| tilted object | draw vertical weight line and compare with base |
Use every explorer once, then test the ideas independently in Practice.