PHYSICS CREST
Physics

Topic 1.5A · Forces A · Effects & Motion

Gravity in calculations: near Earth, g ≈ 9.8 m/s² (9.8 N/kg). Use the value supplied by the question, page instructions or activity; use 10 when it is specified.

Read every force diagram as a story: deformation, spring behaviour, resultant force, acceleration, and the inward force that continuously turns circular motion.

Core force effectsSupplement F = maATP spring & trolley labsDiagram-first notebook
Forces A visual decision board SPRINGx = loaded − originalk = F / xcheck axesRESULTANTsame: addopposite: subtractdirection mattersMOTIONF = maa follows Fcircle: force inward
Name the representation first; then choose the rule.
1
Start with the effect, not the equation

Effects of forces

A force is an interaction that may change an object’s size, shape or velocity. Velocity changes when speed changes, direction changes, or both change.

Four effects begin with one question: what changes? forceforce pull compressed blockstretched spring
Deformation is an effect of force; it does not imply a change of mass.
Horizontal force diagram moving object 4 N10 N All forces act along one straight line
Add same directions; subtract opposite directions; state the resultant direction.
Circular motion: two perpendicular arrows ball inward forcevelocityforce points to centre · velocity is tangent
A change of direction is acceleration even when speed stays constant.

Shape / size

Compression, stretching, bending or twisting.

Speed

A resultant along or opposite motion changes speed.

Direction

A sideways resultant changes the velocity direction.

Effect mnemonicS-S-T

Shape or size · Speed · Turn. State the observable change rather than writing only “it moves.”

Quick check · Can speed stay constant while velocity changes?
Yes. During circular motion the direction changes continuously, so velocity changes even when speed is constant.
Examiner language: “resultant force changes velocity” earns more than “force makes it move.” Always name speed and/or direction.
2
Original length is your zero

Extension and elastic recovery

  • Extension is stretched length minus unloaded length.
  • Record the original length before adding load.
  • Use small load steps, allow oscillation to settle and read a pointer against a fixed scale without parallax.
  • In the proportional region, doubling load doubles extension.
Elastic change: load, extend, recover load remove originalextendedrecovers
“Elastic” describes recovery after unloading.
Spring and ruler arrangement load fixed rulereye-level pointerwait for oscillations
Extension = loaded length − unloaded length.
$x=L-L_0$

Here $L_0$ is the unloaded length, $L$ is the loaded length and $x$ is the extension. Extension is a change in length, not the final length.

Length or extension? unloaded length12.0 cmloaded length15.4 cmextension?
Read the labels and units before choosing a method.

Worked distinction

$x=15.4-12.0=3.4$ cm. Reporting 15.4 cm as the extension would include the spring’s original length.

Interactive · Extension Engine

Loaded minus original

Extension = 3.4 cm
Concept boundary: the end of proportionality is not automatically the elastic limit. A spring may stop obeying proportionality yet still recover when unloaded.
Safe scope: know elastic recovery, but do not treat the elastic limit as an assessed calculation point in this course.
3
Read the axes before reading the slope

Load–extension graphs and spring constant

  • With force vertically and extension horizontally, a straight graph through the origin has gradient k, the spring constant.
  • The limit of proportionality is where this direct proportionality ends.
  • It is not the breaking point and should not be equated automatically with the elastic limit.
  • Avoid overloading the apparatus.

Within the proportional region, force and extension grow in a constant ratio.

$k=\dfrac{F}{x}$    $F=kx$    $x=\dfrac{F}{k}$
force / N against extension / m extension / mforce / N limit of proportionality
With force or load vertical, the straight-region gradient is k.
extension / m against force / N force / Nextension / m
With extension vertical, the straight-region gradient is 1/k.
Graph orientationGradientStiffer spring looks…
force vertically, extension horizontally$\Delta F/\Delta x=k$steeper
extension vertically, force horizontally$\Delta x/\Delta F=1/k$shallower
Comparing spring graph gradients PQ extension / mforce / N
Force is vertical: a steeper line means a larger k.
Interactive · Spring Constant

Use SI extension for N/m

k = 200 N/m
Interactive · Axis Interpreter

What does the gradient mean?

gradient = k
Graph mnemonicF-up → k; x-up → flip

If force is up the page, gradient is $k$. If extension is up the page, take the reciprocal to obtain $k$.

Unit trap: if $x$ is entered in centimetres while $k$ is required in N/m, convert using 1 cm = 0.01 m before dividing.

Pause · explain it yourself

Can the original constant k be used after the force–extension graph stops being proportional?

4
Alternative-to-Practical thinking begins here

Investigating a spring

Spring and ruler arrangement slotted masses fixed rulereye-level pointerwait for oscillations
Extension = loaded length − unloaded length.
  1. Clamp the spring securely beside a vertical millimetre ruler.
  2. Measure the unloaded length from a fixed reference.
  3. Add known loads in equal steps and let oscillations stop.
  4. Read a pointer at eye level and record loaded length.
  5. Calculate extension, repeat and average.
  6. Plot the graph using headings with units.
A high-mark results table load / N0, 1, 2, 3, 4, 5length / cmrepeat 1, repeat 2mean length / cmcalculatedextension / cmmean − original
Read the labels and units before choosing a method.
load / N against extension / m extension / mload / N limit of proportionality
With force or load vertical, the straight-region gradient is k.

Gradient technique

Use two far-apart points on the best-fit line, not two neighbouring raw dots. Draw a large triangle.

Boundary technique

The limit of proportionality is where the points first depart systematically from the straight trend.

Precision chain: fixed ruler + pointer + eye level + settled spring. Each phrase attacks a specific reading error.
Load wording: if masses are supplied, convert mass to weight before plotting force. Do not label a mass axis “load / N.”
Do not claim: “the spring is permanently deformed at the limit of proportionality.” The graph only proves that force and extension are no longer directly proportional.
5
One straight line · one signed sum

Resultant force and constant velocity

  • Draw only forces acting on the chosen object.
  • Add forces along one direction and subtract those opposite.
  • Zero resultant means no acceleration: an object may be at rest or travelling at constant velocity.
  • A force is required to change velocity, not merely to maintain motion in a straight line at steady speed.
Horizontal force diagram crate 9 N14 N All forces act along one straight line
Add same directions; subtract opposite directions; state the resultant direction.
$F_{resultant}=\text{sum of forces in a chosen positive direction}$
Three collinear forces object 22 N east8 N west5 N west
Combine forces by direction before finding the final resultant.

Worked: three forces

Take east as positive: $F_R=22-8-5=9$ N east.

The sign and the arrow direction tell the same physical story.

Balanced forces do not mean “not moving” 18 N18 N possible constant velocity
Zero resultant means zero acceleration: rest or constant velocity are both possible.
ResultantAccelerationPossible motion
zerozeroat rest or constant velocity
non-zerosame direction as resultantspeed and/or direction changes
Interactive · Resultant Calculator

Choose right as positive

Resultant = 5 N right
Resultant mnemonicS-O-D

Same direction: add · Opposite: subtract · Direction: follow the larger total.

Balanced-force trap: zero resultant does not mean “stationary.” It means no change in velocity.

Pause · explain it yourself

A car travels at constant velocity despite engine thrust. What does this imply horizontally?

A moving object has zero resultant force. Which statement is correct?

6
Resultant first · equation second

Newton’s second law

  • In F = ma, F is the resultant.
  • Acceleration points in that direction.
  • If motion is rightward and acceleration leftward, the object initially slows; it does not immediately reverse.
  • Equal and opposite forces on different objects cannot be cancelled on one object’s force diagram.
Cart: use the resultant in F = ma 6.0 kg 24 N
Find the resultant first, then divide by mass. Acceleration follows the resultant direction.
$F=ma$    $a=\dfrac{F}{m}$    $m=\dfrac{F}{a}$

Worked: direct acceleration

$a=24/6.0=4.0$ m/s², in the force direction.

Cart: use the resultant in F = ma 200 kg 900 N drive300 N drag
Find the resultant first, then divide by mass. Acceleration follows the resultant direction.

Worked: resistance included

Resultant $=900-300=600$ N. Then $a=600/200=3.0$ m/s² forward.

Force–mass evidence object · mass · resultantJ · 2.0 kg10 NK · 3.0 kg18 NL · 5.0 kg20 N
Read the labels and units before choosing a method.

Same mass

A greater resultant force gives a greater acceleration.

Same force

A greater mass gives a smaller acceleration.

Interactive · F = ma Engine

Enter the resultant—not one component force

Acceleration = 4.00 m/s² in the resultant direction
Method order: force diagram → resultant force → $F=ma$ → magnitude + direction + unit.
Applied-force trap: in $F=ma$, $F$ means resultant force. If resistance is shown, subtract it first.
Your turn · Extended: find acceleration for a 4 kg mass acted on by a resultant force of 12 N.

Decimals and scientific notation are accepted. Compatible units are accepted.

7
Velocity tangent · force inward

Circular motion

  • Velocity includes direction.
  • In circular motion the instantaneous velocity is tangential and changes direction continuously.
  • The inward resultant is perpendicular to the motion.
  • For fixed mass and radius, greater inward force corresponds to greater speed.
  • For fixed mass and speed, greater inward force corresponds to a smaller radius.
  • Greater mass needs greater inward force for the same speed and radius.
  • These are qualitative syllabus comparisons; an advanced circular-force formula is not needed.
  • The required inward force may be tension, friction or gravity depending on the situation.
Circular motion: two perpendicular arrows car inward forcevelocityforce points to centre · velocity is tangent
A change of direction is acceleration even when speed stays constant.

A force perpendicular to motion can change the direction of velocity continuously. The force is directed towards the centre; instantaneous velocity is tangent to the path.

Qualitative circular-motion comparison tight pathwide pathCompare one variable at a time: mass, speed, radius or force
No numerical circular-force formula is required for this topic.
Held fixedChangePrediction
mass and radiusinward force increasesspeed increases
mass and speedinward force increasesradius decreases
speed and radiusmass increasesgreater inward force is required
Release from circular motion instantaneous velocitypath if inward force ends
Without inward force, the object initially follows the tangent.
Interactive · Circular Relationship Explorer

Change one variable at a time

Prediction: radius decreases.
Direction mnemonicT-I

Tangent velocity · Inward force.

Required level: explain these relationships qualitatively. A numerical circular-force equation is not required here.
“Outward force” trap: do not draw an outward force on the moving object simply because it feels pushed outward. Identify the real inward interaction maintaining the circle.

Pause · explain it yourself

Can an object at constant speed accelerate?

8
Alternative to Practical

ATP Lab Lens: measurements, graphs and evaluation

Spring and ruler arrangement known forces fixed rulereye-level pointerwait for oscillations
Extension = loaded length − unloaded length.
force / N against extension / m extension / mforce / N limit of proportionality
With force or load vertical, the straight-region gradient is k.
Cart: use the resultant in F = ma constant total mass varied pullfriction
Find the resultant first, then divide by mass. Acceleration follows the resultant direction.
Spring planC-O-A-R-G

Clamp and ruler · Original length · Add known loads · Repeat readings · Graph and gradient.

Weak statementExam-ready replacement
“measure carefully”read pointer at eye level after oscillations stop
“repeat”repeat each load, identify anomalies and calculate a mean
“draw graph”label both axes with units, use over half the grid, best-fit trend
“find slope”use a large triangle on the best-fit straight region

Independent

The variable deliberately changed: force or mass.

Dependent

The response measured: extension or acceleration.

Controls

Spring, starting reference, total mass, runway or release method as appropriate.

Error chain: source → effect on reading/gradient → targeted improvement. Example: parallax shifts length → extension is biased → use a pointer and read at eye level.
Trolley investigation: when using a hanger, its weight is an applied pull, not automatically the exact resultant force because friction and pulley resistance may act.
9
One-page visual recall

Topic 1.5A Master Sheet

Forces A visual decision board SPRINGx = loaded − originalk = F / xcheck axesRESULTANTsame: addopposite: subtractdirection mattersMOTIONF = maa follows Fcircle: force inward
Name the representation first; then choose the rule.
Comparing spring graph gradients PQ force / Nextension / m
Axes are reversed: a shallower line means a larger k.
Circular motion: two perpendicular arrows object inward forcevelocityforce points to centre · velocity is tangent
A change of direction is acceleration even when speed stays constant.

Equation bank

$x=L-L_0$
$k=F/x$
$F=ma$

Memory board

SST · shape/size, speed, turn
F-up → k; x-up → flip
SOD · same add, opposite subtract, direction
TI · tangent velocity, inward force
COARG · spring practical
If the question shows…First move
loaded and original lengthsubtract to find extension
spring graphread axes before interpreting gradient
several collinear arrowschoose positive direction and sum
applied and resistive forcesfind resultant before $F=ma$
circular pathdraw force inward, velocity tangent
Final answer audit: resultant rather than component? extension rather than length? centimetres converted to metres? graph axes checked? force and acceleration directions stated?
Interactive mastery: 0 / 6 explored

Use every explorer once, then enter Practice with a clean method.