PHYSICS CREST
Physics

Topic 4.4 · Electrical Safety

Gravity in calculations: near Earth, g ≈ 9.8 m/s² (9.8 N/kg). Use the value supplied by the question, page instructions or activity; use 10 when it is specified.

Identify the hazard, trace the current path, decide what must open, and state exactly what each safety layer protects.

Four mains hazardsLive · neutral · earthFuse & trip logicSafe model-only ATP
1SPOT FAULT2TRACE PATH3COMPARE RATING4OPEN LIVEFAULT → PATH → DEVICE → PROTECTION
Four moves organise almost every electrical-safety explanation.
1
Read safely · reason precisely

Electrical safety is studied through diagrams and data—not by experimenting on mains equipment

1READ FIGURE2NAME FAULT3TRACE CURRENT4STATEPROTECTION
Treat the drawing as evidence: interpret it without touching real equipment.
CURRENT-LIMITED LOW-VOLTAGE MODELLOW-VSUPPLYAMODELTRIPLOAD BANKsafe learning = enclosedlow-voltage model only
Any investigation in these notes uses only a teacher-prepared current-limited low-voltage model.
SEALED IMAGE-CARD SURVEYCARD Asquare-in-squareCARD Bmetal case + earthCARD Csplit cableCARD Ddamp warning
Photographs and examiner-made cards can test safety-feature recognition without handling mains equipment.

Your examiner job is to explain cause and effect. Your practical job is to stay away from live mains circuits. Never open, rewire, test or repair a plug, socket or appliance. Damaged, damp or overheating equipment must be isolated and passed to a responsible adult or qualified person.

Non-negotiable boundary: no learner investigation uses a wall socket, mains cable, real fuse box or opened appliance. Use diagrams, supplied data, sealed image cards or an enclosed current-limited low-voltage model.

Safe exam action

Inspect the figure, trace intended and fault paths, calculate from supplied values and write a causal chain.

Do not try this on real mains equipment

Opening equipment, changing a mains fuse, probing conductors or testing a fault. Leave all mains work to a qualified adult.

Safety firstSEE → THINK → EXPLAIN

Never change the real equipment to prove the physics.

Quick Check · A cable looks split. Should a learner test whether it still works?
No. Stop using it, isolate it without touching exposed conductors and tell a responsible adult. Study the fault using the diagram only.
2
Fault → physical change → danger

Electrical hazards

  • Shock involves dangerous current through the body.
  • Damaged insulation may expose live conductors.
  • Damp conditions can reduce resistance, increasing shock risk.
  • Excess current heats cables and can cause fire, so overloaded extension leads are hazardous even without bare wire.
damaged insulationconductor accessible↓ shockdamp conditionslower-resistance path↓ shockoverloaded extension leadexcess current↓ heating / firehot cableinsulation damage↓ fire / shock
Damaged insulation and damp conditions commonly create shock paths; overload and overheating commonly create thermal/fire hazards.
Syllabus wording to remember: excess current can result from overloading plugs, extension leads, single sockets or multiple-socket outlets. The excessive current heats the cable and can damage insulation or cause a fire.
DAMAGED INSULATIONconductor may beaccessible
Damaged insulation can make a conductor accessible.
DAMP CONDITIONSsealed connectorwater can provideunwanted paths
Water can provide an unwanted conducting path and lower effective resistance.
OVERLOADED DISTRIBUTION LEAD2.1 A3.8 A4.6 Atotal = 10.5 A · rating = 10 AEXCEEDS RATING → overheatingrisk
Parallel appliance currents add. Compare the total with the lead rating.
CABLE OVERHEATINGcontinued high current → heating →insulation damage
Unexpected heating can weaken insulation and increase both fire and shock risk.
Which chain most directly describes a fire risk?
ObservationPhysical changeExam hazard
insulation cut or wornconductor may be accessibleelectric shock
damp / water ingressunwanted path; effective resistance fallselectric shock / fault current
too many loadstotal current exceeds ratingcable heating / fire
cable already hotinsulation can soften or failfire and possible exposed conductor
  1. Name the exact fault or misuse.
  2. State what changes physically: accessible conductor, resistance or current.
  3. State shock, overheating or fire risk.
  4. If data are given, calculate total current and compare numerically with the rating.
MnemonicDAMAGE + DAMP → unwanted paths · OVERLOAD + HEAT → thermal danger

Use the diagram evidence; do not force every situation into only one category.

Examiner language: “current exceeds the cable rating, so the cable heats; prolonged heating can damage insulation and create a fire risk.”
Prevention trap: a fuse does not stop someone overloading a lead. It interrupts the circuit only when sufficient excessive current operates it.
Quick Check · Loads take 2.0 A, 3.5 A and 4.8 A on a 10 A lead. Is it overloaded?
Yes. The total is 10.3 A, which exceeds 10 A, so continued use can overheat the cable.

Pause · explain it yourself

Why is damaged insulation dangerous even if the device still operates?

3
Normal path ≠ safety path

Live, neutral and earth

SUPPLYSEALED APPLIANCELIVENEUTRALEARTHsupplies loadnormal returnfault path onlyNORMAL: live current = neutral current
In normal operation, current enters through live and returns through neutral; earth current is approximately zero.
Earthed appliance · normal operationEarthed appliance · normal operationconducting caseloadfuseliveneutralearth pathNormal current flows through the load and neutral; earth current is approximately zero.
The earth conductor is connected to an accessible metal case but normally carries no current.
Earthed appliance · live-to-case faultEarthed appliance · live-to-case faultconducting caseloadfuseliveneutralearth pathlive touches caseLow-resistance earth path → large fault current → live protection opens.
During a live-to-case fault, the earth conductor becomes part of the fault-current path.
What is the role of the earth conductor?
ConductorNormal roleCurrent in fault-free operation
live (line)connects the appliance to the alternating high potentialload current
neutralcompletes the normal circuitload current
earthlow-resistance safety path from conducting caseapproximately zero
MnemonicLIVE LEADS · NEUTRAL RETURNS · EARTH EMERGES IN A FAULT

Neutral and earth may both be near earth potential in a simplified model, but they are not interchangeable.

Precision: never write “earth completes the circuit”. The appliance already operates through live and neutral.
Colour caution: use conductor names unless the question explicitly asks for a colour. Wiring colours vary with region and historical system.
Quick Check · Does the earth wire carry the same current as neutral during normal operation?
No. Neutral is the normal return path; earth normally carries approximately zero current and carries current only when a fault creates a path.
4
OFF must break LIVE

Switching the live wire

  • Live and neutral carry normal operating current.
  • Earth is a protective connection to exposed conducting casing and should not carry normal operating current.
  • A switch must interrupt live to isolate the appliance from the live supply.
  • Opening neutral can stop operation while leaving internal parts connected to live.
  • State the specific hazard rather than treating every fault as the same mechanism.
APPLIANCELIVENEUTRALSWITCH OPENlive connection broken
Correct: the open switch interrupts the live connection.
APPLIANCELIVENEUTRALSWITCH OPENstill connected to LIVE
Incorrect: the open neutral switch stops normal current but leaves the appliance connected to live.
SUPPLYSEALED APPLIANCEPQRrole ?role ?role ?
In a labelled question, first identify which conductor is live; then place the switch in that path.
Which switch position gives the required safe-off logic?
  1. Find the live conductor.
  2. Locate the switch.
  3. Imagine the switch open.
  4. Trace whether the appliance still has any connection to live.
  5. State the consequence relative to earth.
MnemonicSTOPPED ≠ ISOLATED · OFF MUST OPEN LIVE

No load current is not proof that all parts are disconnected from live.

Two-mark chain: switch in live → opening disconnects the appliance from the high-potential conductor → internal parts are not left connected to live through that path.
Neutral trap: “the appliance turns off” is not enough. A neutral-side switch can turn it off while leaving internal parts live.
Quick Check · Why do the switch and overcurrent device both belong in live?
When either opens, it interrupts the live connection. Placing either only in neutral may stop current while leaving the appliance connected to live.
Why is an appliance switch placed in the live connection?

5
Heat → melt → open

Fuses

ABVCD
Recognise the fuse symbol before explaining its action.
FUSE IN LIVE WIREelement intactcurrent = 3 Arating = 5 A
Below its rating, the fuse element remains intact during normal operation.
FUSE IN LIVE WIREelement heatingcurrent = 9 Arating = 5 A
A sufficiently excessive current causes strong heating of the thin fuse element.
FUSE IN LIVE WIREelement melted → circuit opencurrent = 9 Arating = 5 A
The element melts, the conducting path breaks and current stops.
Complete the fuse-operation chain.
  1. Fault or overload produces excessive current.
  2. The fuse element heats.
  3. The element melts.
  4. The live circuit opens.
  5. Current stops, so continued cable heating is prevented.
Purpose: protect the circuit and cabling from continued excessive-current heating.
Position: live wire.
After operation: replacement by a qualified/responsible adult after the cause is corrected.
MnemonicHIGH I → HEAT → MELT → OPEN

Do not jump from “fault” to “safe”; give the physical mechanism.

Shock trap: a fuse does not guarantee protection if a person touches live and the current is below the fuse rating. Its central syllabus role is overcurrent/cable protection.
Quick Check · Does a fuse prevent a short circuit from starting?
No. The fault starts first and produces excessive current; the fuse then melts and interrupts the circuit.
6
Calculate → compare → choose

Selecting a protective rating

  • Estimate operating current from I = P/V.
  • A suitable available protective rating exceeds normal demand while respecting the stated cable protection limit.
  • Real equipment can have starting currents, so use the given data and manufacturer guidance rather than treating a classroom calculation as wiring instructions.
  • A fuse rating does not force that current through an appliance; circuit resistance and supply determine normal current.
  • An excessively large fuse can fail to protect a lower-rated cable.
  • Explain both conditions when justifying a selection, rather than merely choosing the smallest number in a list.
APPLIANCE LABELpower920 Wsupply p.d.230 Vnormal currentI = P / V
Find the operating current from the values printed in the question.
PROTECTION-RATING DECISION3 A5 A10 A13 Aoperating 4 Acable safe current = 10 Achoose the smallest supplied value above demand and within cablelimit
4.0 A demand: 5 A is the smallest supplied rating above normal current and within the cable limit.
PROTECTION-RATING DECISION2 A3 A5 A10 Aoperating 3 Amaximum stated normal/start-updemand = 4.4 Acable safe current = 10 Achoose the smallest supplied value above demand and within cablelimit
If a start-up current is stated, the selected rating must allow it.
Interactive · Rating coach

Use the printed voltage and supplied choices

I = 4.00 A · smallest supplied rating above I = 5 A
$P=IV$ so $I=P/V$
Choose the smallest supplied rating above the greatest stated normal/start-up current, provided it does not exceed the stated cable safe current.
  1. Use the voltage in the question.
  2. Calculate $I=P/V$ if current is not given.
  3. Include any stated start-up current.
  4. Choose the smallest available higher value.
  5. Check against the stated cable limit.
Boundary case: if no supplied rating is both above the device demand and within the cable limit, say that no listed rating is suitable.
Regional-list trap: never import memorised national fuse values when the question supplies its own choices.
Quick Check · A device takes 7.2 A, cable limit 10 A; choices 3, 5, 10, 13 A. Which?
10 A. It is above 7.2 A and does not exceed the 10 A cable limit.

Pause · explain it yourself

Why is a 13 A fuse unsuitable for a 4 A appliance whose cable must be protected at no more than 5 A?

Your turn · Find normal current for a 690 W appliance connected to the stated 230 V supply.

Decimals and scientific notation are accepted. Compatible units are accepted.

7
Automatic contacts · reset after correction

Circuit breakers and residual-current devices

RESETTABLE OVERCURRENT TRIPcontacts CLOSEDcurrent below settingSET: current can flow
Below the setting, the trip contacts remain closed.
RESETTABLE OVERCURRENT TRIPcontacts OPENcurrent exceeds settingTRIPPED: current interrupted
When the trigger condition is met, the contacts open and interrupt the current.
FUSE IN LIVE WIREelement melted → circuit opencurrent = 8 Arating = 5 A
A fuse opens by melting; a resettable trip device opens by a switching mechanism.
What does an overcurrent trip switch do?
FeatureFuseResettable trip switch
operationelement heats and meltsmechanism opens contacts
restorationreplace after cause correctedreset after cause corrected
shared purposeinterrupt excessive current and protect circuit/cabling
MnemonicFUSE FLOWS ONCE · TRIP TOGGLES AFTER THE FAULT IS FIXED

Resetting is not fault repair.

Scope precision: “trip switch” is a family name. If a question gives an overcurrent setting, explain current above setting → contacts open. Do not automatically describe residual-current sensing.
Speed trap: do not claim every trip switch is always faster than every fuse unless the question provides comparison data.
Quick Check · What must happen before a tripped device is reset?
The cause of the excessive current must be identified and corrected by an appropriate adult/qualified person. Resetting alone does not remove the fault.
8
Live → case → earth → large current → open live

Earthing a metal case

  • If live touches an earthed metal case, the low-resistance earth path allows a large fault current.
  • A suitable fuse melts or overcurrent breaker trips, disconnecting supply.
  • The fuse protects circuit and cabling; it is not a guarantee against every shock.
Earthed appliance · normal operationEarthed appliance · normal operationconducting caseloadfuseliveneutralearth pathNormal current flows through the load and neutral; earth current is approximately zero.
Normal operation: the case is earthed but earth current is approximately zero.
Earthed appliance · live-to-case faultEarthed appliance · live-to-case faultconducting caseloadfuseliveneutralearth pathlive touches caseLow-resistance earth path → large fault current → live protection opens.
Fault: live touches case; a large earth fault current makes the live fuse operate.
Earthed appliance · live-to-case faultEarthed appliance · live-to-case faultconducting caseloadtripliveneutralearth pathlive touches caseHigh earth resistance: smaller fault current; protection may operate too slowly.
A high-resistance fault path can reduce fault current and delay operation.
Why must the earth path have low resistance?
  1. Live conductor touches the conducting case.
  2. The case is connected to earth by a low-resistance path.
  3. A large fault current flows.
  4. The fuse or trip device opens the live circuit.
  5. The duration of the hazardous case potential is reduced.
Fault chainTOUCH → PATH → LARGE I → DEVICE OPENS → LIVE DISCONNECTED

Every arrow can earn a marking point.

Careful claim: the case may become live briefly when the fault begins. Earthing helps the protection operate; it does not make a live-to-case fault impossible.
“Current goes to ground” is incomplete: state that the low-resistance earth fault path allows a large current that operates the fuse/trip device.
Quick Check · Why is a broken earth connection dangerous?
A live-to-case fault may leave the case at a hazardous potential, while the fault current may be too small to operate the protective device promptly.
9
Non-conducting case · insulating barriers

Double insulation

  • Double-insulated appliances use non-conducting protective barriers and do not need an earth to an exposed conducting case.
  • They still need circuit protection.
  • A residual-current device detects imbalance between outgoing and returning current, unlike a simple overcurrent fuse.
  • Keep these mechanisms separate when interpreting a diagram or selecting an explanation.
DOUBLE INSULATION
The square inside a square identifies double-insulated equipment.
DOUBLE-INSULATEDEARTHED METAL CASELIVE PARTSinsulating barriersLIVE PARTSearth
Compare an insulating casing system with a conducting case and earth path.
FUSE IN LIVE WIREelement melted → circuit opencurrent = 8 Arating = 5 A
A fuse still protects a two-core double-insulated appliance from excessive-current cable heating.
Which design explains why no earth wire is needed?

Double insulation

Accessible casing is non-conducting; live parts are separated by insulating barriers; no conducting case needs earthing.

Fuse / trip

Still opens the circuit if excessive current threatens the internal circuit or supply cable.

Two different jobsINSULATION BLOCKS ACCESS · FUSE BLOCKS CONTINUED OVERCURRENT

Never write “no earth, therefore no fuse”.

Core statement: a fuse without an earth wire still protects the circuit and cabling for a double-insulated appliance.
Zero-risk trap: a double-insulation mark does not make a damaged supply cable or overheating safe.
Quick Check · A double-insulated device develops a live-to-neutral short circuit. Which safety feature responds?
The overcurrent protection. The large current makes the fuse melt or the trip device open, protecting the circuit and cable.

Pause · explain it yourself

Why does a double-insulated appliance still need a fuse?

10
Name the layer · name its exact job

Comparing protective measures

WHAT DOES EACH LAYER PROTECT?fuse / overcurrent tripcable + circuitcontinued excessivecurrentearth wireuser at metal caselive-to-case fault pathdouble insulationuser at casingaccess to conductinglive partslive-wire switchoff-stateisolationlive connection whenopen
Each safety layer has a different trigger and protection target.
APPLIANCELIVENEUTRALSWITCH OPENlive connection broken
Live-wire switch: safe-off connection logic.
Earthed appliance · live-to-case faultEarthed appliance · live-to-case faultconducting caseloadtripliveneutralearth pathlive touches caseLow-resistance earth path → large fault current → live protection opens.
Earth plus protection: live-to-case fault-clearing logic.
DOUBLE-INSULATEDEARTHED METAL CASELIVE PARTSinsulating barriersLIVE PARTSearth
Casing choice: non-conducting/double-insulated or conducting/earthed.
FeatureTrigger / conditionActionPrimary protection
live-wire switchuser opens switchbreaks live connectionoff-state isolation
fuseexcess currentheats, melts, openscircuit/cable
trip switchspecified triggeropens contactscircuit/cable for overcurrent device
earthlive-to-metal-case faultlow-R fault pathhelps protection disconnect live
double insulationconstruction featureseparates user from live partsuser at casing
State

Name the hazard, conductor, device or casing type.

Explain

Use linked physical steps in the correct order.

Choose

Calculate demand, compare options and apply the cable limit.

Six-word test: What changes? Where does current flow? What opens? What is protected?
Quick Check · Which feature stops a plastic case becoming a conducting shock path?
The non-conducting/double-insulated casing design. The fuse has a separate job: interrupt excessive current.
11
Alternative to Practical

ATP Lab Lens · model, measure, repeat and evaluate without direct mains work

CURRENT-LIMITED LOW-VOLTAGE MODELLOW-VSUPPLYAMODELTRIPLOAD BANKswitch off between low-voltageload changes
Model-trip investigation: measure current in a current-limited low-voltage circuit only.
THRESHOLD RESULTStrial1 · 2 · 3 · 4 · 5largest no-trip / Arecordsmallest trip / Arecordmidpoint / Acalculate
Bracket a threshold between the last no-trip and first-trip readings.
SEALED IMAGE-CARD SURVEYCARD Asquare-in-squareCARD Bmetal case + earthCARD Csplit cableCARD Ddamp warning
A blinded image-card survey tests classification reliability without opening appliances.
InvestigationIndependentDependentCritical controls
model trip thresholdlow-voltage model currenttrip/no trip; thresholdsupply, device, step size, temperature, on-time
rating simulationdevice current/cable dataselected settingsame rule and supplied options
image-card classificationcard evidencecategory/agreementwritten rules, random order, blind classifiers
  1. State the model or simulation.
  2. Name independent, dependent and control variables.
  3. Use several values and genuine repeats.
  4. Record quantity/unit headings.
  5. Process with a mean, range, bracket or percentage agreement.
  6. Link every limitation to a specific improvement.
Threshold quality: approach from below in small steps, repeat from the same starting condition and quote a bracket or spread—not a falsely exact single value.
ATP safety: enclosed current-limited low voltage only; switch off between model changes; no wall socket, mains plug, real trip board, opened appliance or exposed conductor.
Quick Check · How can trip-threshold repeatability be judged?
Repeat the full threshold search several times under the same controls and compare the range/spread of the threshold estimates.
12
One-page examiner logic

Master Electrical Safety by tracing the dangerous path and the path that must be opened

damaged insulationconductor accessible↓ shockdamp conditionslower-resistance path↓ shockoverloaded extension leadexcess current↓ heating / firehot cableinsulation damage↓ fire / shock
First identify which of the four hazard families the diagram shows.
APPLIANCELIVENEUTRALSWITCH OPENlive connection broken
Safe-off rule: interrupt live.
PROTECTION-RATING DECISION3 A5 A10 A13 Aoperating 4 Acable safe current = 10 Achoose the smallest supplied value above demand and within cablelimit
Rating rule: above demand, closest supplied value, within cable limit.
Earthed appliance · live-to-case faultEarthed appliance · live-to-case faultconducting caseloadfuseliveneutralearth pathlive touches caseLow-resistance earth path → large fault current → live protection opens.
Fault rule: low-resistance earth path → large fault current → live protection opens.
DOUBLE-INSULATEDEARTHED METAL CASELIVE PARTSinsulating barriersLIVE PARTSearth
Casing rule: non-conducting/double-insulated or conducting/earthed.

1 · Spot

Damage, damp, overheating or overload?

2 · Trace

Normal current or fault current? Through which conductor?

3 · Open

Switch, fuse or trip device must interrupt live.

4 · Protect

Name user, case, circuit or cable precisely.

$I=P/V$ · smallest supplied rating above demand · never above stated cable limit
earth fault: live → case → low-R earth → large current → protection opens live
double insulation: non-conducting accessible case + insulating barriers; fuse still protects circuit/cable
Final chainFAULT → PATH → CURRENT → DEVICE → DISCONNECTION → PROTECTION

For rating questions insert: calculate → compare → choose → cable check.

Final check · What four errors should you scan for?
Switch/fuse wrongly placed in neutral; earth described as normal return; fuse claimed to prevent every shock; double insulation claimed to remove the need for overcurrent protection.
Interactive mastery: 0 / 8 explored

Explore all eight checkpoints, then move to the independent Practice and Exam Arena banks.