Skip to lesson
PCPHYSICS CRESTGlobal Physics AcademyReach the Peak of Understanding.
1

Unit 8 · Fluids

Current Unit 8 boundary
Four official topics: 8.1 Internal Structure and Density, 8.2 Pressure, 8.3 Fluids and Newton’s Laws, and 8.4 Fluids and Conservation Laws. Flow questions use an ideal-fluid model unless stated otherwise.

Use g = 9.8 m/s² and water density 1000 kg/m³ unless specified. Flow is steady along a streamline, and pipes are completely filled, with no leakage, unless the scenario states otherwise.

8.1 · Internal Structure and Density

Fluid
A fluid has no fixed shape. Liquids and gases are fluids because their particles can rearrange and the material can flow.
Ideal fluid model
For AP Physics 1 flow problems an ideal fluid is incompressible and has no viscosity. This deliberately removes density changes and dissipative internal friction.
\[\rho=\frac{m}{V}\]

Mass is not density

A large low-density object can have more mass than a small high-density object.

Volume is not density

Changing the amount of a uniform material changes mass and volume together; density stays the same.
Quick Check 1
A 0.90 kg sample occupies \(7.5\times10^{-4}\,\mathrm{m^3}\). What is its density?
\(\rho=0.90/(7.5\times10^{-4})=1.20\times10^3\,\mathrm{kg\,m^{-3}}\).
Particles and pressure: constituent particles exert forces when they interact with a boundary. The total normal force per area is pressure. An ideal incompressible fluid keeps the same density and volume when pressure changes; nonviscous means dissipative internal shear is neglected.
Given measurementssolidparticles maintainrelative positionsliquid or gasparticles rearrangematerial can flow
2

Density as a Representation

The graph technique AP keeps reusing

Graph of mass m against volume Vvolume Vmass m0slope = density ρ

For one uniform material, \(m=\rho V\).

Mass vs volume: slope \(=\Delta m/\Delta V=\rho\).

Volume vs mass: slope \(=1/\rho\). Always read the axes first.

Density lab routine
Measure several \(m,V\) pairs, plot all data, use a best-fit line, and obtain density from the correct slope. For an irregular object, volume may be found by fluid displacement if the object does not dissolve, absorb liquid, or trap significant air.
Common mistake
A steeper \(m\)-vs-\(V\) line means a greater density; the density of each sample does not increase merely because the sample is larger.
Worked reading: If a best-fit line rises by \(0.36\) kg while volume increases by \(1.5\times10^{-4}\,\mathrm{m^3}\), then \(\rho=2.4\times10^3\,\mathrm{kg\,m^{-3}}\).
Quick Check 2
Two mass-volume lines pass through the origin. Material B has twice the slope of A. Compare densities.
On an \(m\)-vs-\(V\) graph slope is density, so \(\rho_B=2\rho_A\).
3

8.2 · Pressure

  • Fluid pressure describes perpendicular force per area.
  • Buoyancy results from pressure differences over an immersed object.
  • A moving fluid also connects pressure, speed and height through ideal-flow energy reasoning.
Pressure on a surface
\[P=\frac{F_\perp}{A}\] Use the perpendicular force component. Pressure is scalar; the contact force itself has a direction.
Same force, smaller area\(P\) increases.
Same pressure, larger area\(F=PA\) increases.
AP language trap
Pressure is not force. A narrow and wide base at the same depth can have the same pressure but different forces because \(F=PA\).

Why static fluid force is normal to a surface

Any persistent tangential stress in the ideal static-fluid model would make the fluid move. The contact force from a fluid at rest is therefore perpendicular to the surface.

Worked example: A piston receives a perpendicular force of 360 N over \(0.024\,\mathrm{m^2}\). Then \(P=1.50\times10^4\,\mathrm{Pa}\).
Quick Check 3
The same 240 N perpendicular force is applied to half the original area. What happens to pressure?
Pressure doubles because \(P=F_\perp/A\).
Surface under a perpendicular applied force; given area and forceFpressure P = F⊥/Aforce normal to surface
Your turn · Find liquid pressure increase at depth 0.50 m for density 1000 kg/m³ and g = 9.8 m/s².

Decimals, scientific notation and compatible units are accepted. Keep any required sign.

4

Hydrostatic Pressure Intelligence

\[P_{\rm abs}=P_{\rm surface}+\rho gh\]\[P_g=P_{\rm abs}-P_{\rm atm}\]
surfacehhP gaugeslope = ρg

For constant density, gauge pressure grows linearly with depth.

On a \(P_{\rm gauge}\)-vs-\(h\) graph, slope \(=\rho g\).

At the same depth in one connected static fluid, pressure is the same.

Connected and layered fluids

U tube: oil column 0.15 m above interface; water column 0.12 m above the same levelwater surfaceoil surface0.12 m0.15 mreference levelconnected water
Use a common horizontal level in the connected water. Oil is less dense, so its balancing column is taller.
Absolute vs gauge
\(\rho gh\) is pressure above the reference pressure. If absolute pressure is requested, include \(P_0\), often atmospheric pressure.
Quick Check 4
Oil of density \(800\,\mathrm{kg\,m^{-3}}\) is 0.20 m deep above 0.30 m of water. Find bottom gauge pressure.
\(P_g=(800)(9.8)(0.20)+(1000)(9.8)(0.30)=4.51\times10^3\,\mathrm{Pa}\).
Open versus sealed surface: only when the surface is at atmospheric pressure does standard gauge pressure reduce to \(P_g=\rho gh\). In a sealed vessel, \(P_g=(P_{surface}-P_{atm})+\rho gh\). The term \(\rho gh\) is always the pressure increase below the surface for a uniform static liquid; the surface pressure must be included separately.
5

8.3 · Buoyancy from Newton’s Laws

  • Buoyant force equals the weight of displaced fluid.
  • For a floating object, buoyant force balances weight.
  • In steady incompressible flow, volume flow rate Av is constant.
  • Bernoulli reasoning needs the stated ideal-flow conditions and a consistent streamline.
Archimedes principle
\[F_B=\rho_{\rm fluid}gV_{\rm displaced}\] The buoyant force equals the weight of the displaced fluid.
F_Bmglower face is deeper → larger pressurenet pressure force is upward

The lower face is deeper, so it experiences greater pressure than the upper face. The pressure-force imbalance is upward.

For a fully submerged object in a uniform incompressible fluid, \(V_{\rm displaced}=V_{\rm object}\).

Depth trap
For the same fully submerged object in a uniform incompressible liquid, buoyant force is independent of depth. Absolute pressures increase with depth, but their difference remains the same.

Volume matters

Same fluid + same displaced volume → same \(F_B\), even if masses or depths differ.

Fluid density matters

Same displaced volume in a denser fluid → larger \(F_B\).
Quick Check 5
Two fully submerged equal-volume blocks are at different depths in the same liquid. Compare buoyant forces.
Equal: \(F_B=\rho_f gV\), and all three quantities are the same.
Newton’s laws also describe moving fluid. For a horizontal fluid parcel of cross-sectional area A and length L, end pressures exert opposite forces. Ignoring other axial forces, \(F_{net}=(P_L-P_R)A\). With mass \(m=\rho AL\), \(a=(P_L-P_R)/(\rho L)\). A parcel can have constant nonzero velocity when its net force is zero; pressure differences can accelerate a parcel.
A floating object is in equilibrium. Which forces are equal in magnitude?

6

Floating, Sinking & Force Diagrams

V_subfloating at rest:F_B = mgV_sub/V = ρ_obj/ρ_fluid

For a freely floating object at rest, \(F_B=mg\).

\[\frac{V_{\rm sub}}{V}=\frac{\rho_o}{\rho_f}\]

Held down by a string attached below
Forces: \(F_B\) upward; \(mg\) and tension downward. At rest, \(F_B=mg+T\).
Held up by a string from above
Forces: \(F_B+T=mg\) for a dense suspended object at rest.
Float/sink language
A floating object at equilibrium does not have \(F_B>mg\). That would produce upward acceleration. Floating equilibrium means \(F_B=mg\).
Fraction submerged: A block of density \(720\,\mathrm{kg\,m^{-3}}\) floats in water. \(V_{\rm sub}/V=0.720\), so 72% is submerged.
Quick Check 6
A 900 kg/m³ block floats in a 1200 kg/m³ liquid. What fraction is submerged?
\(V_{sub}/V=900/1200=0.75\).
7

Buoyancy + Acceleration + Systems

Immediately after a constraint is removed

For a fully submerged object of density \(\rho_o\) in fluid density \(\rho_f\), with drag neglected:

\[a=\frac{F_B-mg}{m}=g\left(\frac{\rho_f}{\rho_o}-1\right)\]
Example: A \(750\,\mathrm{kg\,m^{-3}}\) sphere is released fully submerged in water. \(a=9.8(1000/750-1)=3.27\,\mathrm{m\,s^{-2}}\) upward while it remains fully submerged and drag is negligible.

Container/scale reaction idea

If an external support holds a submerged object without touching the container, the liquid exerts \(F_B\) upward on the object, so the object exerts \(F_B\) downward on the liquid. The container’s support reading increases by that amount.

System selection
For a floating raft + attached-load system at rest, total displaced-fluid weight equals total system weight. Moving the load deeper can redistribute the displaced volume between load and raft while total displaced volume stays fixed for fixed fluid density and system weight.
Quick Check 7
A fully submerged object is less dense than the fluid and is released with drag negligible. Initial acceleration direction?
Upward, because \(F_B=\rho_f gV>\rho_o gV=mg\).
Container of water with submerged object; labelled given dimensionsopen surfacewaterless-dense objectreleased from restnet force up
8

8.4 · Continuity = Mass Conservation

Volume flow rate
\[Q=\frac{\Delta V}{\Delta t}=Av\]
Incompressible continuity
\[A_1v_1=A_2v_2\]
A₁, v₁A₂, v₂A₁v₁ = A₂v₂

For fixed volume flow rate in a filled pipe with no leaks, a smaller cross-sectional area gives a larger speed.

For circular pipes, \(A=\pi r^2\), so radius and diameter ratios must be squared.

Pipe length is irrelevant to continuity in the ideal steady-flow model.

Radius trap: If radius halves, area becomes one quarter, so speed becomes four times larger—not twice as large.
Do not confuse
Continuity gives the speed relation. It does not by itself determine pressure.
Quick Check 8
A circular pipe radius decreases from 4 cm to 2 cm. Initial speed is 1.5 m/s. Find new speed.
Area falls by a factor of 4, so \(v_2=6.0\,\mathrm{m\,s^{-1}}\).
Boundary conditions must agree. In steady flow through a horizontal, completely filled, constant-area ideal pipe, equal inlet and outlet speeds require equal inlet and outlet pressures. A nonzero pressure difference across such a section cannot simultaneously satisfy this steady ideal model without another energy transfer.
9

Bernoulli = Energy Accounting

\[P+\rho gy+\frac12\rho v^2=\text{constant along a streamline in steady ideal flow}\]
Two Bernoulli energy bar charts with missing pressure barpoint 110P2ρgy3½ρv²point 24P5ρgy6½ρv²Energy per volume in kPa

Think of three energy-per-volume accounts:

Pressure\(P\)
Gravitational\(\rho gy\)
Kinetic\(\tfrac12\rho v^2\)

The safest two-step method

  1. Continuity first: determine \(v_2\) from areas.
  2. Bernoulli second: compare \(P,\rho gy,\tfrac12\rho v^2\).
Horizontal shortcut—only when horizontal
At equal height, faster flow means lower pressure in this ideal model. If both height and speed change, pressure can be greater than, less than, or equal to the original pressure.
Competing changes: Fluid rises (tends to lower \(P\)) but slows (tends to raise \(P\)). Write Bernoulli instead of guessing.
Quick Check 9
In a horizontal ideal pipe speed rises from 2 m/s to 5 m/s. What happens to pressure?
Pressure decreases because the kinetic-energy-per-volume term increases while height is unchanged.
10

Torricelli + Projectile Motion

Horizontal jet from open tank; head and drop height separately labelledopen surfaceh = ΔyHRhorizontal outlet
h is the surface-to-hole head; H is the hole-to-floor drop. They are different vertical distances.

Jet range is a two-model problem

After the fluid leaves horizontally, it follows projectile motion. If the hole is height \(H\) above the floor, \(t=\sqrt{2H/g}\), so

\[R=v_{\rm exit}\sqrt{\frac{2H}{g}}\]
Experimental linearization
Move the entire tank while preserving its surface-to-hole head and replenishing the liquid; this keeps exit speed fixed. Vary drop height \(H\). Plot \(R\) versus \(\sqrt H\): slope \(S=v_{\rm exit}\sqrt{2/g}\), hence \(v_{\rm exit}=S\sqrt{g/2}\).
Torricelli assumptions
Same reference pressure at surface and outlet, ideal fluid, reservoir-surface speed negligible, and \(\Delta y\) is the vertical separation between surface and hole.
Quick Check 10
An open tank has a hole 1.80 m below the surface. Estimate exit speed.
\(v=\sqrt{2(9.8)(1.80)}=5.94\,\mathrm{m\,s^{-1}}\).
Where is pressure measured? At the atmospheric free outlet, gauge pressure is zero. At a point S in nearly stationary bulk liquid at the outlet height, well away from the accelerating region, \(P_{g,S}\approx\rho gh\). Bernoulli from S to the free outlet gives \(P_{g,S}\approx\tfrac12\rho v_{exit}^2\); it does not assign that pressure to the moving outlet itself.
11

AP Lab & Representation Routines

balance → mvolume → VVm

A strong AP experiment answer

  1. states what is varied and measured,
  2. uses several trials over a useful range,
  3. transforms data into a linear graph,
  4. connects slope/intercept to the requested quantity.

Density from graph

\(m=\rho V\): plot \(m\) vs \(V\); slope \(=\rho\).

Hydrostatic density

\(P_g=\rho gh\): plot \(P_g\) vs \(h\); slope \(=\rho g\).

Jet speed

\(R=v\sqrt{2H/g}\): plot \(R\) vs \(\sqrt H\).

Pressure-speed density

For a nearly stationary bulk-fluid point S and an atmospheric outlet O at equal height, Bernoulli gives \(P_{g,S}=\tfrac12\rho v^2\). Plot \(P_{g,S}\) vs \(v^2\); slope \(=\rho/2\). Change the head between trials to obtain different speeds; do not measure pressure in the free jet, where gauge pressure is zero.
TBR: move between FBDs, pressure-depth graphs, flow-speed graphs, Bernoulli bar charts, and equations.
QQT: predict first, then verify with functional dependence or equations.
Quick Check 11
A \(P_g\)-vs-\(h\) graph has slope \(8.82\times10^3\,\mathrm{Pa/m}\). Estimate fluid density.
\(\rho=\text{slope}/g=900\,\mathrm{kg\,m^{-3}}\).
12

Unit 8 · AP Master Sheet

Core relations

Density\(\rho=m/V\)
Pressure\(P=F_\perp/A\)
Hydrostatic\(P_{\rm abs}=P_{surface}+\rho gh\); for an atmospheric open surface, \(P_g=\rho gh\)
Buoyancy\(F_B=\rho_f gV_{\rm displaced}\)
Floating fraction\(V_{\rm sub}/V=\rho_o/\rho_f\)
Flow rate\(Q=Av\)
Continuity\(A_1v_1=A_2v_2\)
Bernoulli\(P+\rho gy+\tfrac12\rho v^2=\text{constant}\)
Torricelli\(v=\sqrt{2g\Delta y}\)
Final traps
  • mass, weight, volume, size, and density are not interchangeable;
  • same depth → same pressure, not necessarily same force;
  • floating at rest means \(F_B=mg\);
  • fully submerged \(F_B\) is depth-independent in a uniform incompressible fluid;
  • radius ratios are squared in continuity;
  • “faster means lower pressure” is only a safe shortcut at equal height;
  • gauge pressure omits the reference pressure;
  • Torricelli is a special Bernoulli result and needs its assumptions.
Four current AP routines
MR: derive/compute. TBR: make representations agree. LAB: design, linearize, interpret slope. QQT: predict, then quantitatively verify.
Quick Check 12
A floating block is moved from water to a denser liquid. After equilibrium, what happens to buoyant force and submerged fraction?
Buoyant force remains \(mg\), while the submerged fraction decreases.
Given measurementsstatic fluidpressure grows with depthbuoyancy: net fluid forcesteady ideal flowmass is conservedmechanical energy conserved