WONDER — The Mystery
One Disturbance, Different Travel Times
A flash reaches an observer before the thunder because light and sound have very different speeds. Sound speed depends on the material, its elastic response, density and state. Steel rod, water and air are useful examples, but “all solids are faster than all gases” is not a universal rule.
Model: Uniform still media and small disturbances. For dry air near ordinary temperatures we use the enrichment approximation c ≈ 331 + .6T, with c in m/s and T in °C. Water has the illustrative fixed speed 1500 m/s; longitudinal waves in the chosen slender steel rod use 5000 m/s. These are model values, not universal constants for every liquid or steel geometry. Audible air is treated as non-dispersive.
PREDICT — Commit to Your Answer
DOK 2 — PredictDry air warms from 0 °C to 30 °C without changing gas composition. In the ordinary-temperature model, sound speed:
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
The stated approximation gives 331 m/s and 349 m/s. The temperature dependence of an ideal gas uses absolute temperature, not a Celsius ratio.
▶ PLAY — Live Pulse Travel in Three Media
DOK 2 — InvestigatePredict, measure and compare
Measure a baseline in 0 °C air, change only air temperature, then change only medium. Compare distances after the same .020 s. Try frequency alone too.
A pulse front emitted at t = 0 moves at x = ct through a uniform medium. The displayed track spans 100 m at 3.6 pixels/m. Every run covers .020 physical seconds over six real seconds, so front position rather than equal-screen crossing time shows the speed difference. The colored marker follows the wave front; its rings are schematic and it is not a material particle. Air uses c ≈ 331 + .6T over −20 to 40 °C. Water and the selected slender steel rod use fixed illustrative speeds 1500 and 5000 m/s; the air-temperature control is unused for those cases. Wavelength readouts describe a periodic tone at the chosen frequency, not the width of this schematic pulse.
Status: Ready
Playback: 6 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — State the Material and the Model
DOK 1 — RecallFlip all 4 rule cards. Keep the quantities and model conditions clear.
Rule 1
Elasticity and density
Click to flip
Elasticity and density
A fluid’s small-signal speed obeys c = √(B/ρ), with B the appropriate bulk modulus and ρ the density. This detailed relation is extension. Stiffness and inertia must be considered together; greater density reduces speed only if the elastic modulus is held fixed. Different kinds of solid wave have different elastic-modulus relations.
Rule 2
Dry air and temperature
Click to flip
Dry air and temperature
For a fixed ideal-gas composition, c scales with √T_K. The classroom approximation c ≈ 331 + .6T_C is useful near ordinary temperatures, not near absolute zero or over arbitrary temperature ranges. Water and steel also have state-dependent speeds; fixed values in this lab deliberately omit that dependence.
Rule 3
Periodic waves and pulse travel
Click to flip
Periodic waves and pulse travel
For periodic waves c = fλ. The source frequency remains unchanged at a stationary boundary, while wavelength adjusts to the new speed. In this non-dispersive model increasing frequency does not increase c. A pulse travel time follows distance divided by speed; a pulse need not have a unique wavelength.
Rule 4
Timing a signal
Click to flip
Timing a signal
One-way travel gives d = ct. An echo returning to the source travels twice the boundary distance, so d = ct_echo/2. For simultaneous light and sound signals, delay = d/c_sound − d/c_light; the light term is negligible only under the stated ordinary-distance approximation.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “Every solid transmits sound faster than every gas.”
Correct — the claim is false.
False. The familiar steel–water–air ranking applies to the stated examples; actual speeds depend on material properties and wave type.
Myth 2: “Doubling audible frequency doubles speed in the same still-air model.”
Correct — the claim is false.
False. The model is non-dispersive: c stays fixed and wavelength halves.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Travel, Frequency and Material Conditions
DOK 2 — ApplyUse the stated approximation only within its ordinary-temperature range.
Instructor Q1 — Material Comparison
Which controls sound speed?
Instructor Q2 — Frequency Change
Same air conditions; frequency doubles. Wavelength:
Instructor Q3 — Warm Air
Use the taught dry-air approximation for 20 °C. Find c.
Instructor Q4 — One-Way Flight
A pulse travels 51.0 m at 340 m/s. Find its one-way travel time.
4/4 — Instructor Questions Completed
Choose the wave type and material conditions; then connect distance, time and periodic wavelength.
✎ PRACTICE — Independent Speed and Timing Audits
DOK 1–3 — PracticeChallenge 1: A Cool Day
Dry air is at 10.0 °C. Find the sound speed predicted by the ordinary-temperature approximation taught in this mission.
Step-by-Step Solution
c ≈ 331 + .6×10.0 = 337 m/s.
Challenge 2: An Underwater Echo
A sound echo returns to its stationary source after .0920 s in water where c = 1500 m/s. The reflector is stationary and the path is straight. Find its distance from the source and the wavelength of a 60.0 kHz periodic signal in that water.
Step-by-Step Solution
Distance = 1500×.0920/2 = 69.0 m. λ = 1500/60000 = .0250 m.
Challenge 3: Audit a Controlled Experiment
A straight 120 m air path is tested at 0 °C and 30 °C using the taught dry-air approximation. A 1.00 kHz tone is used both times. Find the decrease in one-way travel time and the warm-air wavelength. A report says doubling source frequency would double speed, density alone proves that water must be slower than air, and the approximate air formula remains valid at every temperature. Correct all three claims and identify what must be controlled when testing the temperature effect.
Explanation checks are indicative. Compare your reasoning with the worked solution or your teacher.
Step-by-Step Solution
Speeds are 331 and 349 m/s. The time decrease is 120/331 − 120/349 = .01869822 s. Warm λ = 349/1000 = .349 m. Same-air speed is independent of frequency in this model. Elastic response and density jointly control speed, so density alone cannot rank different materials. The linear temperature approximation is limited to ordinary dry-air conditions. Keep path length, gas composition, flow and the timing method controlled.
☷ CHALLENGE — Classify the Speed Statement
DOK 2 — ApplyClassify the Speed Statement
Select each statement and place it in its matching category. Judge the physical conditions.
0 / 6 correct
Physics Insight
Choose the wave type and material conditions; then connect distance, time and periodic wavelength.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Explain why light arrives before sound, what material properties control sound speed, and how one-way timing differs from echoes.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 13.3 — Speed of Sound
Reach the Peak of Understanding
1. Elasticity and density
A fluid’s small-signal speed obeys c = √(B/ρ), with B the appropriate bulk modulus and ρ the density. This detailed relation is extension. Stiffness and inertia must be considered together; greater density reduces speed only if the elastic modulus is held fixed. Different kinds of solid wave have different elastic-modulus relations.
2. Dry air and temperature
For a fixed ideal-gas composition, c scales with √T_K. The classroom approximation c ≈ 331 + .6T_C is useful near ordinary temperatures, not near absolute zero or over arbitrary temperature ranges. Water and steel also have state-dependent speeds; fixed values in this lab deliberately omit that dependence.
3. Periodic waves and pulse travel
For periodic waves c = fλ. The source frequency remains unchanged at a stationary boundary, while wavelength adjusts to the new speed. In this non-dispersive model increasing frequency does not increase c. A pulse travel time follows distance divided by speed; a pulse need not have a unique wavelength.
4. Timing a signal
One-way travel gives d = ct. An echo returning to the source travels twice the boundary distance, so d = ct_echo/2. For simultaneous light and sound signals, delay = d/c_sound − d/c_light; the light term is negligible only under the stated ordinary-distance approximation.
Worked independent practice
C1: 337 m/s. C2: 69.0 m and .0250 m. C3: .01869822 s decrease and .349 m, with model limitations and controls explained.
Live investigation and access
A pulse front emitted at t = 0 moves at x = ct through a uniform medium. The displayed track spans 100 m at 3.6 pixels/m. Every run covers .020 physical seconds over six real seconds, so front position rather than equal-screen crossing time shows the speed difference. The colored marker follows the wave front; its rings are schematic and it is not a material particle. Air uses c ≈ 331 + .6T over −20 to 40 °C. Water and the selected slender steel rod use fixed illustrative speeds 1500 and 5000 m/s; the air-temperature control is unused for those cases. Wavelength readouts describe a periodic tone at the chosen frequency, not the width of this schematic pulse.
Run, Pause, Step and Reset work offline. Complete three matched measurements. Loading a preset is not completing a trial. Saved progress resumes paused. Reduced-motion Run gives a final snapshot; Step allows deliberate inspection. Hints and solutions require a genuine unsuccessful numerical attempt and never complete a task. Explanation rubrics are indicative; compare your physics with the solution or a teacher. Teaching submission checks effort rather than certifying scientific accuracy.
Course scope
Cambridge AS wave-speed relationships and AP Physics 2 sound-speed temperature trends are core. The linear dry-air formula, bulk-modulus relation and detailed material comparisons are supporting enrichment. The selected steel value is for an illustrative longitudinal rod model.
Sources: Cambridge International 9702 syllabus ; College Board AP Physics 2 CED. Detailed extension models are labelled in the mission.
✓ Crest’s Checklist
- I specify material conditions and wave type.
- I avoid universal solid/liquid/gas rankings.
- I qualify the dry-air approximation.
- I separate sound speed from particle velocity.
- I distinguish one-way timing from round trips.
— Crest ☆ “Reach the Peak of Understanding”
Mission 13.3 Complete! · All 10 levels cleared · PHYSICS CREST
★ Speed of Sound Investigator
Choose the wave type and material conditions; then connect distance, time and periodic wavelength.