WONDER — The Mystery
A Force Perpendicular to Two Directions
A nonmagnetic wire carrying current in an imposed magnetic field can accelerate sideways. The current direction and field direction alone determine the vector force; an arrow drawn simply perpendicular to the wire can still be wrong if it is not also perpendicular to the field.
Model: For a straight segment in a uniform imposed field, Fvector = I Lvector × Bvector and magnitude F = |I|LB sinθ, where θ is between the specified positive length direction and B. The nonzero force is perpendicular to both. Current reversal reverses its direction. Forces from other circuit segments, magnetized materials and mechanical constraints need separate consideration.
PREDICT — Commit to Your Answer
DOK 2 — PredictConventional current points upward on the page and the imposed field points into the page. What is the force direction on that wire segment?
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
With +y current and −z field, +y × (−z) = −x, leftward. Fleming’s left-hand motor rule gives the same result.
▶ PLAY — A Wire Accelerating Out of Its Initial Plane
DOK 2 — InvestigatePredict, measure and compare
Compare two currents at one angle, then two angles at one current. Run and watch the segment’s physical displacement in a separate +z-axis view. Check current reversal, zero current and antiparallel alignment.
A straight nonmagnetic segment has L = 0.10 m and mass 0.020 kg, starts at rest and is constrained to translate along z while its orientation stays fixed. B = 0.50 T points +x. The positive length direction is (cosθ, sinθ, 0), so Fz = −ILB sinθ. An ideal regulated current source maintains I; flexible leads and other circuit segments are arranged so their forces do not affect the measured segment. The uniform field covers its full displacement, gravity is supported, and friction is neglected. Thus az = Fz/m, vz = azt and z = ½azt². A 0.20 s physical interval plays over 6 real seconds. The top view identifies current/field geometry; the lower side-view marker is the physical wire position along z. The source supplies the mechanical energy and compensates motional e.m.f.; the static field is not free energy.
Status: Ready
Playback: 6 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — Magnitude, Vector Direction and Energy
DOK 1 — RecallFlip all 4 rule cards. Keep the quantities and model conditions clear.
Rule 1
The segment model
Click to flip
The segment model
Magnitude F = |I|LB sinθ applies to a straight segment of length L entirely in a uniform imposed B. L is the length in the field, not automatically the whole circuit length. For a nonuniform field use the force contributions along the conductor.
Rule 2
Find the vector direction
Click to flip
Find the vector direction
For positive conventional current use L × B. Reverse current or field to reverse force; reverse both to restore it. Fleming’s left-hand rule uses first finger B, second finger conventional I and thumb force. A right-hand cross-product rule gives the same physics.
Rule 3
Parallel and antiparallel
Click to flip
Parallel and antiparallel
The magnitude is maximal at 90° for fixed |I|, L and B, and zero at both 0° and 180°. If I = 0 the I L × B contribution is zero in this nonmagnetic-wire model. A zero force vector has no direction.
Rule 4
Point charge versus circuit
Click to flip
Point charge versus circuit
An isolated charge’s magnetic Lorentz force qv × B is perpendicular to its total velocity and does no instantaneous work on that charge. A moving current-carrying conductor belongs to a powered circuit; electrical energy can become mechanical energy. Do not infer that a whole wire can never gain kinetic energy.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “The force on a wire is always along the current direction.”
Correct — the claim is false.
False. The nonzero I L × B force is perpendicular to both the current-bearing segment and imposed field.
Myth 2: “A current-carrying wire cannot accelerate because magnetic force does no work on an isolated point charge.”
Correct — the claim is false.
False. The conductor/circuit system can exchange electrical and mechanical energy; it is not an isolated point charge.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Angle and Length Checks
DOK 2 — ApplyWork with the stated imposed field and conductor segment.
Instructor Q1 — Opposite Alignment
The positive current direction is antiparallel to B. What is the magnetic force?
Instructor Q2 — Current Reversal
Reverse current while leaving geometry and B unchanged. A nonzero force:
Instructor Q3 — Perpendicular Segment
I = 5.0 A, L = 2.0 m and B = 0.50 T, with I perpendicular to B. Find force magnitude.
Instructor Q4 — Tilted Segment
I = 4.0 A, L = 0.50 m, B = 0.40 T and θ = 30°. Find force magnitude.
4/4 — Instructor Questions Completed
Use a three-dimensional cross product before drawing the force. A perpendicular arrow in the current–field plane is generally incorrect.
✎ PRACTICE — Independent Force and Motion Audits
DOK 1–3 — PracticeChallenge 1: Perpendicular Wire Force
A straight wire segment carrying 4.0 A has 0.50 m of its length in a uniform imposed 2.0 T field. The segment is perpendicular to the field. Find the magnetic force magnitude.
Step-by-Step Solution
F = |I|LB sin90° = 4.0 × 0.50 × 2.0 = 4.0 N.
Challenge 2: Field Length and Angle
A 0.80 m wire carries current through a region where only 0.20 m lies in a uniform 0.30 T imposed field. That segment makes 30° to B and experiences force magnitude 0.12 N. Find the current magnitude. With this current maintained, find the force magnitude if that same 0.20 m segment is rotated to 90°.
Step-by-Step Solution
|I| = 0.12/(0.20×0.30×0.50) = 4.0 A. At 90°, F = 4.0×0.20×0.30 = 0.24 N.
Challenge 3: Audit the Accelerating-Wire Report
A nonmagnetic 0.10 m segment of mass 0.020 kg carries 2.0 A along +y in uniform B = 0.30 T along +x. It starts at rest and is free to translate along z, with gravity supported and no friction; a regulated source maintains current. Find signed Fz and displacement z after 0.10 s. A report says “force is upward along current, and the wire cannot gain kinetic energy because the magnetic force does no work on a charge.” Correct both claims and identify the energy source. Explain how reversing current changes force and displacement.
Explanation checks are indicative. Compare your reasoning with the worked solution or your teacher.
Step-by-Step Solution
+y × +x = −z. Fz = −2.0×0.10×0.30 = −0.060 N; az = −0.060/0.020 = −3.0 m/s²; z = ½(−3.0)(0.10)² = −0.015 m. The force is perpendicular to current and field. The electrical source supplies mechanical energy while maintaining current and compensating induced e.m.f.; the point-charge magnetic no-work result does not prohibit conductor motion. Reversing current reverses force, acceleration and displacement in this model.
☷ CHALLENGE — Force Changes in a Uniform Field
DOK 2 — ApplyForce Changes in a Uniform Field
Select each statement and place it in its matching category. Judge the physical conditions.
0 / 6 correct
Physics Insight
Use a three-dimensional cross product before drawing the force. A perpendicular arrow in the current–field plane is generally incorrect.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Explain magnitude and vector direction of the motor-effect force, both zero-force angles, the interacting length, and the energy source when a wire accelerates.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 11.9 — Magnetic Force on a Current-Carrying Wire
Reach the Peak of Understanding
1. The segment model
Magnitude F = |I|LB sinθ applies to a straight segment of length L entirely in a uniform imposed B. L is the length in the field, not automatically the whole circuit length. For a nonuniform field use the force contributions along the conductor.
2. Find the vector direction
For positive conventional current use L × B. Reverse current or field to reverse force; reverse both to restore it. Fleming’s left-hand rule uses first finger B, second finger conventional I and thumb force. A right-hand cross-product rule gives the same physics.
3. Parallel and antiparallel
The magnitude is maximal at 90° for fixed |I|, L and B, and zero at both 0° and 180°. If I = 0 the I L × B contribution is zero in this nonmagnetic-wire model. A zero force vector has no direction.
4. Point charge versus circuit
An isolated charge’s magnetic Lorentz force qv × B is perpendicular to its total velocity and does no instantaneous work on that charge. A moving current-carrying conductor belongs to a powered circuit; electrical energy can become mechanical energy. Do not infer that a whole wire can never gain kinetic energy.
5. Carrier derivation
For one carrier species in a uniform conductor, J = nqvdrift as a vector, so force density J × B integrates to I L × B. Electron charge and drift direction are both opposite to the positive-charge convention, giving the same conventional-current force direction. Do not multiply signed electron charge by a positive speed and ignore its vector direction.
6. Motion and energy
For a constant net constrained force, a = F/m, v = at and displacement = ½at² from rest. Mechanical work F·displacement equals the kinetic-energy increase in this frictionless model. A regulated source must provide the associated electrical energy; real circuits also dissipate heat.
7. Device scope
A current-carrying loop can have zero net force but a nonzero torque in uniform B. Loudspeaker voice coils and motor coils use forces distributed around their conductors. The single straight-segment force is a local model rather than a complete device description.
Worked independent practice
C1: 4 N. C2: 4 A and 0.24 N. C3: Fz = −0.060 N and z = −0.015 m; the electrical source supplies energy, and current reversal reverses the signed response.
Live investigation and access
A straight nonmagnetic segment has L = 0.10 m and mass 0.020 kg, starts at rest and is constrained to translate along z while its orientation stays fixed. B = 0.50 T points +x. The positive length direction is (cosθ, sinθ, 0), so Fz = −ILB sinθ. An ideal regulated current source maintains I; flexible leads and other circuit segments are arranged so their forces do not affect the measured segment. The uniform field covers its full displacement, gravity is supported, and friction is neglected. Thus az = Fz/m, vz = azt and z = ½azt². A 0.20 s physical interval plays over 6 real seconds. The top view identifies current/field geometry; the lower side-view marker is the physical wire position along z. The source supplies the mechanical energy and compensates motional e.m.f.; the static field is not free energy.
Run, Pause, Step and Reset work offline. Complete three matched measurements. Loading a preset is not completing a trial. Saved progress resumes paused. Reduced-motion Run gives a final snapshot; Step allows deliberate inspection. Hints and solutions require a genuine unsuccessful numerical attempt and never complete a task. Explanation rubrics are indicative; compare your physics with the solution or a teacher. Teaching submission checks effort rather than certifying scientific accuracy.
Course scope
A Level 9702 20.2 includes F = BIL sinθ and Fleming’s left-hand rule. AP Physics 2 12.3 includes force magnitude and direction on current-carrying wires. Constrained-segment dynamics and detailed circuit-energy discussion extend these ideas; ideal regulated-current and uniform-field assumptions are stated.
Sources: Cambridge International 9702 syllabus ; College Board AP Physics 2 CED. Detailed extension models are labelled in the mission.
✓ Crest’s Checklist
- I use the length in the field.
- I distinguish magnitude from signed components.
- I check both 0° and 180°.
- I use conventional current for the force rule.
- I track electrical and mechanical energy in the whole circuit.
— Crest ☆ “Reach the Peak of Understanding”
Mission 11.9 Complete! · All 10 levels cleared · PHYSICS CREST
★ Magnetic Force on a Current-Carrying Wire Investigator
Use a three-dimensional cross product before drawing the force. A perpendicular arrow in the current–field plane is generally incorrect.