WONDER — The Mystery
Same Resistors, Different Equivalent Resistance
Reconnecting the same positive resistors changes the current paths and therefore the source current. Series resistances add because the current is shared and voltage drops add. Parallel conductances add because branch p.d. is shared and currents add. Always identify the actual topology before choosing a shortcut.
Model: Use positive finite fixed resistances, ideal wires and ideal constant-p.d. sources. The two live diagrams are separate circuits with the same selected source p.d. and resistor values. Kirchhoff’s junction rule represents charge conservation; its loop rule represents energy conservation.
PREDICT — Commit to Your Answer
DOK 2 — PredictTwo resistors, 4 Ω and 8 Ω, are in parallel between the same two nodes. How does the equivalent resistance compare with 4 Ω?
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
1/Req = 1/4 + 1/8, so Req = 8/3 Ω, less than 4 Ω. Their branch currents need not be equal.
▶ PLAY — Live Side-by-Side Circuit Analyzer
DOK 2 — InvestigatePredict, measure and compare
Run two A resistances with all other values fixed, then change only source p.d. Complete three runs. Both separate circuits animate together. Compare equivalent resistance, source current, series voltage drops and parallel branch currents.
The same A, B and C resistances are used in two separate ideal circuits: all three in series on the left, all three in parallel on the right. Req,s = A + B + C and Req,p = [1/A + 1/B + 1/C]⁻¹. Series drops are IsRk; each parallel current is V/Rk. A run lasts 8 model seconds over 8 real seconds. Moving dots show conventional current with schematic counts and speeds, not individual electrons. Source energy grows as VIs t or VIp t; resistor powers sum to the corresponding source power.
Status: Ready
Playback: 8 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — Derive and Check the Shortcuts
DOK 1 — RecallFlip all 4 rule cards. Keep the quantities and model conditions clear.
Rule 1
Series sums
Click to flip
Series sums
Shared current gives V = IΣR, hence Req = ΣR. Each drop is IRk and the drops sum to source p.d.
Rule 2
Parallel reciprocals
Click to flip
Parallel reciprocals
Shared p.d. gives Itotal = VΣ(1/Rk), hence 1/Req = Σ(1/Rk). For exactly two resistors, Req = RARB/(RA + RB).
Rule 3
Equal branches only
Click to flip
Equal branches only
Req = R/N applies only when all N parallel resistances equal R. Unequal branches require the reciprocal sum. A final reciprocal is essential.
Rule 4
Conservation checks
Click to flip
Conservation checks
At a junction, signed current balance expresses charge conservation. Around a loop, algebraic p.d. changes sum to zero. The total passive resistor power equals source output in this ideal model.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “For any two parallel resistors, take the first resistance divided by two.”
Correct — the claim is false.
False. R/2 applies only to two equal resistors; use the reciprocal sum for unequal values.
Myth 2: “The sum of parallel branch p.d.s equals source p.d.”
Correct — the claim is false.
False. Each branch has the source p.d.; it is branch currents that add.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Equivalent Resistance and Conservation
DOK 2 — ApplyUse positive finite resistances and ideal source conditions.
Instructor Q1 — Series Check
Which calculation checks energy conservation around a simple source-and-series-resistors loop?
Instructor Q2 — Parallel Check
Which check follows charge conservation at a source junction?
Instructor Q3 — Series Equivalent
Three positive resistors 2 Ω, 5 Ω and 7 Ω form one series path. Find equivalent resistance.
Instructor Q4 — Parallel Equivalent
Resistors 6 Ω and 18 Ω share the same two nodes. Find equivalent resistance.
4/4 — Instructor Questions Completed
A plausible equivalent resistance must also satisfy branch and loop measurements.
✎ PRACTICE — Independent Circuit Calculations
DOK 1–3 — PracticeChallenge 1: Unequal Series Loads
Resistors A = 4 Ω and B = 7 Ω are in series across an ideal 22 V source. Find equivalent resistance, source current and p.d. across B.
Step-by-Step Solution
Req = 4 + 7 = 11 Ω; I = 22/11 = 2 A. VB = 2 × 7 = 14 V and VA = 8 V.
Challenge 2: Unequal Parallel Loads
Resistors A = 8 Ω and B = 12 Ω are in parallel across an ideal 24 V source. Find equivalent resistance, source current and current in A.
Step-by-Step Solution
Req = 8 × 12/(8 + 12) = 4.8 Ω. IA = 24/8 = 3 A, IB = 2 A and Itotal = 5 A.
Challenge 3: Audit a Parallel Calculation
A = 5 Ω and B = 10 Ω are in parallel across an ideal 15 V source. A report adds their resistances directly, assigns the entire source current to each branch, and says opening B leaves source current unchanged. Find initial equivalent resistance, initial source current and source current after B is opened. Explain all three errors.
Step-by-Step Solution
Req = 5 × 10/(5 + 10) = 10/3 Ω. IA = 3 A and IB = 1.5 A; their sum is 4.5 A. Opening B removes its 1.5 A contribution, so source current falls to 3 A while A’s current remains unchanged. Use reciprocal resistance addition and junction conservation.
☷ CHALLENGE — Series, Parallel or Both Checks?
DOK 2 — ApplySeries, Parallel or Both Checks?
Use the stated positive-resistance ideal-circuit models.
0 / 6 correct
Physics Insight
The formulas arise from physical conservation, not visual similarity.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Derive the series and parallel formulas from loop and junction conservation, explain the unequal-branch case, and give independent checks for a calculation.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 10.8 — Series & Parallel Calculations
Calculate equivalent resistance, then verify charge and energy conservation.
1. Series derivation
I is shared. The loop rule gives Vsource = IR1 + IR2 + … = IΣR, so Req = ΣR. Each drop Vk = IRk. For at least two strictly positive resistances, Req exceeds the largest individual resistance.
2. Parallel derivation
V is shared across the same two nodes. Junction conservation gives Itotal = V/R1 + V/R2 + … = VΣ(1/R). Thus 1/Req = Σ(1/R). Invert the conductance sum to obtain resistance; a number in Ω⁻¹ is not yet Req in Ω.
3. Useful shortcuts
For two positive parallel resistors, Req = R1R2/(R1 + R2). For N equal branches, Req = R/N. Neither shortcut authorizes combining elements that do not share the required path or pair of nodes.
4. Bounds and branch checks
A positive finite parallel equivalent is below the smallest individual branch resistance. Verify Itotal = ΣIk and Vk equal for branches between the same nodes. Unequal resistances generally give unequal parallel currents.
5. Loop signs and power
Choose a traversal direction and assign source rises and resistor drops consistently; their algebraic sum is zero. For passive ideal resistor circuits, Vsource Itotal = ΣIk²Rk. The loop rule expresses energy conservation; the junction rule expresses charge conservation.
6. Fault changes
Opening a parallel branch removes its current contribution. With an ideal fixed-p.d. source, surviving branch currents remain unchanged while source current decreases. Opening the only series path instead gives zero settled current throughout it.
Worked practice
C1: 11 Ω, 2 A and VB = 14 V. C2: 4.8 Ω, 5 A source and 3 A in A. C3: 10/3 Ω, 4.5 A initially and 3 A after B opens; correct the reciprocal sum, branch-current assignment and fault response.
Experiment and access
The same A, B and C resistances are used in two separate ideal circuits: all three in series on the left, all three in parallel on the right. Req,s = A + B + C and Req,p = [1/A + 1/B + 1/C]⁻¹. Series drops are IsRk; each parallel current is V/Rk. A run lasts 8 model seconds over 8 real seconds. Moving dots show conventional current with schematic counts and speeds, not individual electrons. Source energy grows as VIs t or VIp t; resistor powers sum to the corresponding source power.
Predict before Run. Complete three matched measurements; loading a preset does not complete a trial. Pause, Step and Reset work offline. Saved progress resumes paused. Reduced-motion preference uses a completed snapshot on Run. Hints and solutions become available only after a genuine numerical attempt and do not complete a challenge. Teaching checks effort; compare your explanation with these notes or a teacher.
Course scope
Cambridge AS 9702 topic 10.2 and AP Physics 2 topics 11.5–11.7 cover combinations, junction conservation and loop conservation. The shortcuts apply only to genuine series or parallel groups.
✓ Crest’s Checklist
- I identify topology from paths and nodes.
- I take the final reciprocal for parallel resistance.
- I use R/N only for equal parallel branches.
- I verify the junction-current sum.
- I verify loop drops and total power.
— Crest ☆ “Calculate equivalent resistance, then verify charge and energy conservation.”
Mission 10.8 Complete! · All 10 levels cleared · PHYSICS CREST
★ Series & Parallel Calculations Master
A plausible equivalent resistance must also satisfy branch and loop measurements.