WONDER — The Mystery
Same Throughput, Different Speeds
A completely filled pipe narrows. In a steady incompressible flow without leaks or branches, equal volumes cross each section in equal times. How can the fluid move faster in the narrow section without becoming more densely packed? Does this determine what happens to a real tap’s throughput after its outlet is changed?
Model: Steady flow through a completely filled unbranched pipe with no mass accumulation. Section speed means the cross-section average. For uniform density, volume flow Q = Av is constant along the pipe. More generally steady one-dimensional mass flow is ρAv. These conservation relations alone do not fix flow rate from a pump or tap; source pressure, losses and system dynamics also matter.
PREDICT — Commit to Your Answer
DOK 2 — PredictSteady incompressible flow passes through a filled circular pipe with diameter 6 cm in one section and 3 cm in another. There are no leaks or branches. How does the average speed in the smaller section compare with the larger section?
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
Circular area is proportional to diameter squared. A2/A1 = (3/6)² = 1/4. With A1v1 = A2v2, v2 = 4v1.
▶ PLAY — Live Tracers through a Filled Variable-Area Pipe
DOK 2 — InvestigatePredict, measure and compare
Compare two outlet areas while keeping regulated volume flow and density fixed. Then change only regulated flow from one of that pair. Complete three runs. Watch a tagged parcel cross the pipe and compare speeds, volume throughput and mass throughput.
A prescribed steady incompressible plug-flow approximation uses A1 = 0.0040 m². The pipe is 2.00 m long: 0.80 m at A1, 0.40 m with linearly changing area, then 0.80 m at A2. The source regulates the selected Q; the pressure and work needed to establish that flow are outside this kinematic lab. Local speed is Q/A(x). Tracers use cumulative fluid-volume coordinates, so they move faster where area is smaller without compressing the fluid. A gold parcel travels from inlet to outlet; cyan markers continuously enter and leave an already full pipe. Inlet and outlet throughput both start immediately. Length uses 170 pixels/m and drawn radius scales with square-root area. One parcel’s physical transit is compressed or expanded to 8 real seconds.
Status: Ready
Playback: 8 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — Volume, Mass, Area and Conditions
DOK 1 — RecallFlip all 4 rule cards. Keep the quantities and model conditions clear.
Rule 1
Volume flow is a rate
Click to flip
Volume flow is a rate
Q = ΔV/Δt = Av for section-average normal speed in the one-dimensional model. Units are m³/s; speed uses m/s. A faster speed alone does not mean greater volume throughput.
Rule 2
Mass conservation is more general
Click to flip
Mass conservation is more general
For steady one-dimensional flow with no branches, leaks or accumulation, ρ1A1v1 = ρ2A2v2. Equal density reduces this to A1v1 = A2v2. Changing density can give different volume flow rates.
Rule 3
Square circular diameters
Click to flip
Square circular diameters
A = π(d/2)². At the same volume flow, halving diameter quarters area and quadruples average speed. Halving area only doubles speed.
Rule 4
Separate along-flow and between-run claims
Click to flip
Separate along-flow and between-run claims
Continuity conserves flow along a stated steady incompressible run. It does not guarantee equal Q before and after a real nozzle change. A regulated source can hold Q fixed; a fixed-pressure source with losses may respond differently.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “Faster flow in a narrower section means incompressible particles bunch up to a higher density.”
Correct — the claim is false.
False. Uniform density remains unchanged. The same volume per second crosses a smaller area at greater speed; tracer separation along the flow can increase rather than indicate compression.
Myth 2: “Continuity guarantees a real tap keeps exactly the same flow rate after any nozzle change.”
Correct — the claim is false.
False. The relation links sections in one steady run. Changes to geometry can change source flow rate through pressure and loss conditions. This lab explicitly regulates Q for its matched comparisons.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Rates and Area Ratios
DOK 2 — ApplyState the steady-flow assumptions and keep volume rate separate from speed.
Instructor Q1 — What Is Conserved?
What is equal along a filled unbranched steady incompressible pipe without leaks?
Instructor Q2 — Changing Gas Density
In steady one-dimensional compressible flow, which quantity is conserved without leaks or branches?
Instructor Q3 — Fresh Volume Flow
Average speed is 1.5 m/s through area 0.0080 m². Find the volume flow rate.
Instructor Q4 — Fresh Area Change
Steady incompressible flow has A1 = 0.0030 m², A2 = 0.0010 m² and v1 = 0.60 m/s. Find v2.
4/4 — Instructor Questions Completed
Continuity conserves throughput along a specified steady flow. Pressure and energy determine which flow the source can sustain.
✎ PRACTICE — Independent Flow Measurements
DOK 1–3 — PracticeChallenge 1: Volume Collected through a Circular Pipe
A filled circular pipe has internal diameter 0.0400 m. Steady flow delivers 0.0120 m³ in 30.0 s. Find volume flow rate and average pipe speed.
Step-by-Step Solution
Q = 0.0120/30.0 = 0.000400 m³/s. Area = π(0.0400/2)² = 0.00125664 m². Average speed = Q/A = 0.31831 m/s.
Challenge 2: Two Sections and Mass Throughput
A filled pipe carries steady incompressible liquid of density 900 kg/m³ without leaks or branches. Section areas are 0.0060 m² and 0.0015 m². The first-section average speed is 0.80 m/s. Find the second speed, mass flow rate and volume passing either section in 12.0 s.
Step-by-Step Solution
Q = 0.0060(0.80) = 0.00480 m³/s. Second speed = 0.00480/0.0015 = 3.20 m/s. Mass flow = 900(0.00480) = 4.32 kg/s. Volume in 12.0 s = 0.00480(12.0) = 0.0576 m³.
Challenge 3: Audit a Compressible-Flow Report
A steady one-dimensional gas flow has no branches, leaks or mass accumulation. At section 1, density is 2.0 kg/m³, area is 0.010 m² and average speed is 3.0 m/s. At section 2, density is 1.0 kg/m³ and area is 0.0050 m². A report uses the area ratio alone for speed, insists both volume flow rates are equal despite the changing density, and claims continuity alone fixes a real pump’s throughput after a nozzle is changed. Find section-2 speed, both volume flow rates and the conserved mass flow rate. Explain all three errors.
Step-by-Step Solution
Mass flow = 2.0(0.010)(3.0) = 0.060 kg/s. At section 2, v2 = 0.060/[1.0(0.0050)] = 12.0 m/s. Q1 = 0.030 m³/s and Q2 = 0.060 m³/s. Lower gas density permits greater volume rate at the same mass rate.
The area-only speed rule and equal-volume-flow claim require constant density, absent here. Continuity constrains mass throughput along this stated steady flow; it does not determine a changed pump/nozzle operating point without pressure, energy and loss information.
☷ CHALLENGE — Sort Geometry, Conservation and Source Conditions
DOK 2 — ApplySort Geometry, Conservation and Source Conditions
Place each statement with the idea it uses.
0 / 6 correct
Physics Insight
Mass conservation survives density change; constant volume flow needs an additional constant-density condition.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Explain why a narrower section of a filled steady incompressible pipe has greater average speed at the same throughput without compressing the fluid. Explain the difference between volume flow and mass flow, and why continuity alone does not guarantee fixed flow after changing a real tap nozzle.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 7.9 — Fluid Flow and Continuity
Conserve mass flow. Link average speed to cross-sectional area.
1. Volume flow and average speed
Q = ΔV/Δt = Avaverage
Q is volume per time in m³/s. Average section speed is in m/s. For a nonuniform velocity profile, the area average of its normal component gives Q/A. The lab uses a simplified plug-flow profile. Pressure and energy are not determined by continuity alone.
2. Steady mass conservation
ρ1A1v1 = ρ2A2v2
This section relation requires steady one-dimensional flow with no branches, leaks or accumulation between the sections. The broader conservation law includes storage and other inlet/outlet terms. Do not call the simple two-section equation universal for every unsteady or branching system.
If density is constant, A1v1 = A2v2 = Q. This conserves volume throughput along that run, without requiring equal speed or pressure.
3. Circular area ratios
A = π(d/2)²; v2/v1 = A1/A2 at common Q
Halving diameter quarters area and gives four times the speed at the same Q. Halving area gives twice the speed. The first practice gives Q = 0.000400 m³/s and speed 0.31831 m/s for a 0.0400 m diameter.
4. Volume and mass rates
1 L = 0.001 m³; 1 m³/s = 1000 L/s. Mass flow is ρQ in kg/s. The second practice has Q = 0.00480 m³/s, second speed 3.20 m/s, mass flow 4.32 kg/s and volume 0.0576 m³ in 12.0 s.
The gas audit conserves 0.060 kg/s. Changing density gives Q1 = 0.030 m³/s and Q2 = 0.060 m³/s, with v2 = 12.0 m/s. Equal volume flow is not valid for that density change.
5. A changed nozzle is a new source condition
Continuity compares sections within one stated steady flow. A new nozzle may change a real pump or tap’s volume rate because source pressure and losses determine its operating point. The live lab holds Q fixed by explicit regulation. It does not claim a real tap does this automatically.
Greater exit speed alone does not fix jet range. Height, launch angle, gravity and drag also matter. No medical conclusions about vessel damage follow from this ideal conservation model.
6. Live tracer motion
The 2.00 m pipe has a 0.80 m inlet section, a 0.40 m linear-area transition and a 0.80 m outlet section. Local velocity is Q/A(x). Cumulative fluid volume s(x) = ∫A(x)dx advances by Qt for a parcel. Inverting that volume coordinate gives its actual position at the displayed physical time.
The gold parcel starts at the inlet. Cyan tracers continuously enter and leave a pipe already filled at the beginning. Both inlet and outlet therefore pass volume Qt from the start; the gold parcel’s transit delay is not a delay in all outlet flow.
Lengths use 170 pixels/m; drawn radius scales with square-root area. Tracers indicate advected markers, not compressing liquid molecules. One transit plays over 8 real seconds. Compare outlet areas, then regulated Q, keeping other controls fixed.
7. Course scope
Steady incompressible continuity and volume flow directly support AP Physics 1 topic 8.4. Continuity is extension material beyond the named Cambridge AS Level 9702 fluid content. The compressible-flow mass relation is an explicit generalization, not a requirement to treat every AP liquid exercise as compressible.
✓ Crest’s Checklist
- I distinguish speed from volume and mass rates.
- I use section-average normal speed in Q = Av.
- I state no-accumulation, leak and branch assumptions.
- I square circular diameter ratios.
- I retain density in compressible mass flow.
- I distinguish one run from a changed source condition.
- I read tracer position at the same physical time as the measurements.
— Crest ☆ “Conserve mass flow. Link average speed to cross-sectional area.”
Mission 7.9 Complete! · All 10 levels cleared · PHYSICS CREST
★ Continuity Equation Master
Continuity conserves throughput along a specified steady flow. Pressure and energy determine which flow the source can sustain.