Skip to lesson
PC

PHYSICS CREST

Global Physics Academy

Mission 7.7 · Archimedes’ Principle Measure the fluid displaced. Account for the whole system.
Journey Tracker
Progress
0/10
1

WONDER — The Mystery

Weigh the Fluid That Was Pushed Aside

Lower an irregular solid into a brim-full overflow can and collect the liquid it pushes aside. How does the collected liquid relate to buoyancy? Does density alone identify a particular contaminant in a sample?

Overflow measurementBrim-full canFully wet rigid solidSeparate collector
Given conditions only; arrows and distances are schematic.

Model: Hydrostatic buoyancy with uniform fluid, constant g, full fluid contact and negligible surface tension. Displaced volume is the volume excluded from the liquid, not automatically the entire object. Overflow measurements need a can initially at its spout level, no trapped bubbles and complete collection. A density difference can reject a supplied uniform-solid reference model but cannot uniquely establish composition.

2

PREDICT — Commit to Your Answer

DOK 2 — Predict

An overflow can and its water initially read 16 N on a scale. A 4 N object is gently added and floats freely at rest. All overflow drains to a collector off the scale. After overflow finishes, what is the can-scale reading? Neglect surface tension and air buoyancy.

Floating-system givensInitial scale: 16 NFloating object: 4 NOverflow leaves scaleFinal state: at rest
Given conditions only; arrows and distances are schematic.

Commit to both a prediction and a reason before revealing the explanation.

Step 1: Pick your answer.

STOP! Before revealing — why did you pick that?

3

▶ PLAY — Live Overflow and Collection Lab

DOK 2 — Investigate

Predict, measure and compare

Compare two cube sides at the same fluid density and lowering speed. Then change only fluid density from one of that pair. Complete three runs. Watch partial submersion, overflow travel and collection; compare buoyancy with collected plus travelling fluid weight.

A rigid cube of density 3000 kg/m³ begins with its bottom at the liquid surface. An upper support lowers it at constant speed until fully submerged, then holds it. Starting and stopping inertia, drag and air buoyancy are neglected. g = 9.8 m/s². An ideal overflow can stays at its spout level. The transport model routes overflow to a separate collector with a prescribed 0.25 s delay; moving tracer dots show transport, not ballistic falling drops. Fluid still travelling is counted. Buoyancy equals the weight of collected plus travelling displaced liquid during entry, and collected weight alone once collection finishes. Tank lengths use 1000 pixels/m; collector fill is schematic. Each run includes the final delay and plays over 8 real seconds.

Use the labelled readouts.

Status: Ready

Playback: 8 real seconds per run; read elapsed physical model time. Pause or Step for measurements.

Measurements

Physical elapsed time:
Submerged fraction:
Displaced volume:
Collected volume:
Volume still in transit:
Collected fluid mass:
Buoyant force:
Collected fluid weight:
Travelling fluid weight:
Upper-support tension:

Load givens — then predict and run

Loading a setup earns no trial credit.

4

♢ DISCOVER — Displacement, Force and Evidence

DOK 1 — Recall

Flip all 4 rule cards. Keep the quantities and model conditions clear.

Rule 1

Archimedes’ principle

Click to flip

Archimedes’ principle

Under hydrostatic full-contact conditions, buoyancy equals the weight of fluid displaced: B = ρfluid gVdisplaced. It is a force in N, not a mass in kg.

Rule 2

Use the submerged volume

Click to flip

Use the submerged volume

Full submersion of a sealed rigid object displaces its external volume. Partial submersion displaces only the volume below the surface. Open cavities filled with fluid do not exclude that fluid.

Rule 3

Track collection and the system boundary

Click to flip

Track collection and the system boundary

During transport some overflow may still be travelling. Full collection gives displaced-fluid weight. A freely floating object at rest displaces its own weight; an externally supported object need not.

∫

Rule 4

Density tests have limits

Click to flip

Density tests have limits

For a fully wetted rigid solid with no trapped bubbles, collected volume gives excluded volume and ρobject = m/V. A mismatch can reject the reference density under the stated assumptions. It does not uniquely identify an alloy or prove a historical accusation.

Flip all 4 cards to reveal the rules. 0/4 flipped
5

MISCONCEPTION ATTACK — Destroy the Myths

DOK 2 — Analyze

Choose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.

Myth 1: “Buoyancy always equals the object’s own weight.”

Myth 2: “A lower measured density uniquely proves one particular contaminant.”

6

✦ THE SECOND “AHA!” — Displaced Fluid in Liquids and Gases

DOK 2 — Apply

Keep mass, weight, excluded volume and collection conditions separate.

Progress
0/4
Overflow measurementBrim-full canFully wet rigid solidSeparate collector
Given conditions only; arrows and distances are schematic.

1

Instructor Q1 — The Principle

Which is the general Archimedes relation under the hydrostatic model?

2

Instructor Q2 — Partial Submersion

A rigid cube is halfway below the surface, with air buoyancy neglected. Which volume enters the liquid buoyancy calculation?

3

Instructor Q3 — Collected Weight

After all overflow is collected, its mass is 0.24 kg. Use g = 10 m/s². Find its weight.

Collection givensCollected mass: 0.24 kgg: 10 m/s²All overflow collected
Given conditions only; arrows and distances are schematic.
N
4

Instructor Q4 — Air Is a Fluid

A balloon excludes 20 m³ of air of density 1.2 kg/m³. Use g = 10 m/s². Find its gross buoyant force before subtracting any balloon-system weight.

Air-displacement givensVolume: 20 m³Air: 1.2 kg/m³g: 10 m/s²
Given conditions only; arrows and distances are schematic.
N
7

✎ PRACTICE — Independent Displacement Evidence

DOK 1–3 — Practice
DOK 1 — Routine

Challenge 1: Overflow in a Fresh Liquid

A rigid solid is fully submerged in a brim-full can. After complete collection, the overflow volume is 375 mL. The liquid density is 960 kg/m³ and g = 10 m/s². No bubbles or leaks occur. Find displaced fluid mass and buoyant force.

Collected-fluid givensOverflow: 375 mLLiquid: 960 kg/m³g: 10 m/s²Collection complete
Given conditions only; arrows and distances are schematic.
kg
N
DOK 2 — Application

Challenge 2: Balloon System in Air

A balloon system excludes 120 m³ of air of density 1.2 kg/m³. Its total mass, including gas, envelope and payload, is 110 kg. Use g = 10 m/s². At the instant considered there is no drag or tether force. Find gross buoyancy, total weight and net upward force.

Balloon-system givensExternal volume: 120 m³Air: 1.2 kg/m³Total mass: 110 kgg: 10 m/s²; no drag
Given conditions only; arrows and distances are schematic.
N
N
N
DOK 3 — Audit & Justify

Challenge 3: Audit a Density-Test Claim

A solid sample of mass 0.800 kg is fully submerged in water of density 1000 kg/m³. Complete overflow collection gives 50.0 mL. There are no trapped bubbles, open pores, leaks or measurement uncertainty in this model; g = 10 m/s². A supplied uniform reference solid has density 20000 kg/m³. A report treats 50.0 mL as 50.0 m³, sets buoyancy equal to the sample’s weight, and claims the density uniquely identifies a specific added metal. Find displaced volume in m³, sample density and buoyancy. Explain all three errors and state what the comparison actually establishes.

Density-test givensSample mass: 0.800 kgOverflow: 50.0 mLWater: 1000 kg/m³Reference: 20000 (SI)g: 10; no bubbles
Given conditions only; arrows and distances are schematic.
m³
kg/m³
N
8

☷ CHALLENGE — Sort Measurement, Force and Inference

DOK 2 — Apply

Sort Measurement, Force and Inference

Classify each statement by its role in the investigation.

0 / 6 correct

9

TEACH — The Feynman Technique

DOK 3 — Teach

Your Final Mission: Explain how overflow measures displaced volume, why buoyancy equals the weight of that fluid, and why collection during transport may lag displacement. Explain the difference between gross balloon buoyancy and net lift, and one limit of a density-based material test.

Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.

Type Your Explanation (≥ 3 sentences)

Final reward below

Hidden exam secrets inside — Crest's private notebook.