WONDER — The Mystery
The Same Force, a Different Pressure
A broad support and a narrow support carry the same perpendicular force. Why can they produce different average contact pressures? If the applied force is tilted, which part of it compresses the surface? Pressure connects the normal push to the actual contact area.
Model: Average compressive contact pressure is the magnitude of normal force divided by contact area. For a uniform pressure, normal force is PA. Pressure is scalar; the associated force on a surface is a vector normal to that surface. The foundation in Stage 3 has its own supplied elastic law; penetration or damage cannot be predicted from pressure alone without material information.
PREDICT — Commit to Your Answer
DOK 2 — PredictA 48 N perpendicular force acts on either a broad pad of area 0.080 m² or a narrow pad of area 0.020 m². Compare the average pressure from the narrow pad with that from the broad pad.
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
P = Fnormal/A. With the same force, pressure is inversely proportional to area. The narrow pad has one quarter of the area and therefore four times the pressure.
▶ PLAY — Live Pressure Ramp on an Elastic Foundation
DOK 2 — InvestigatePredict, measure and compare
Compare two contact areas with the same final applied force and force angle. Then change only final force from one of that pair. Complete three matched runs. Watch the loaded plate move and the foundation compress as normal force and pressure rise. Compare pressure with the model’s deformation, keeping its stiffness fixed.
A massless rigid square plate presses uniformly on an ideal elastic foundation. Its supplied pressure-to-compression stiffness is K = 100000 Pa/m, giving pressure P = Kδ. Applied force rises linearly from zero to the chosen final value over 2 physical seconds, played over 8 real seconds. Angle is measured from the downward surface normal. The guide carries the horizontal force component; normal force is F cos(angle). Quasi-static motion ignores inertia and damping, and plate weight is zero. The plate’s drawn width represents the square root of contact area; vertical compression uses 400 pixels/m. This is a specific elastic model, not a universal relation between pressure and dent depth or a universal cutting threshold.
Status: Ready
Playback: 8 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Average Pressure vs Physical Time
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — Normal Force, Area, Units and Model Limits
DOK 1 — RecallFlip all 4 rule cards. Keep the quantities and model conditions clear.
Rule 1
The perpendicular component
Click to flip
The perpendicular component
Paverage = Fnormal/A. If the applied force makes angle θ with the surface normal, Fnormal = F cos θ. A tangential component does not contribute to this average compressive pressure.
Rule 2
Area and force are independent
Click to flip
Area and force are independent
With normal force fixed, P is inversely proportional to A. With area fixed, P is proportional to normal force. Changing both can leave pressure unchanged.
Rule 3
SI units and squared conversions
Click to flip
SI units and squared conversions
1 Pa = 1 N/m²; 1 kPa = 1000 Pa. 1 cm² = 10⁻⁴ m² and 1 mm² = 10⁻⁶ m². A rectangular contact area is length times width, in consistent units.
Rule 4
Pressure is scalar; response needs a model
Click to flip
Pressure is scalar; response needs a model
Pressure has magnitude and no vector direction. Its surface force has a normal direction. Material deformation, cutting or failure depends on material properties and geometry as well as pressure.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “Equal applied forces always give equal pressure.”
Correct — the claim is false.
False. Contact area matters, and a tilted force may have a different normal component. Equal normal force and equal actual contact area give equal average pressure.
Myth 2: “A pressure above 10000 Pa must cut or pierce every material.”
Correct — the claim is false.
False. A universal pressure-only penetration threshold is not valid. Material stiffness, strength, contact geometry and other conditions affect deformation and failure. The live model explicitly supplies its elastic law.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Pressure Without the Common Shortcuts
DOK 2 — ApplyUse the normal component, calculate the actual area and convert squared units carefully.
Instructor Q1 — The Appropriate Force
Which force belongs in average compressive contact pressure?
Instructor Q2 — Doubling Both Quantities
Normal force and contact area both double. What happens to average pressure?
Instructor Q3 — A Fresh Pressure
A 72 N normal force acts uniformly over 0.060 m². Find pressure in Pa.
Instructor Q4 — Find the Normal Force
Uniform pressure is 6.0 kPa over area 0.015 m². Find the normal force in N.
4/4 — Instructor Questions Completed
A force is a vector. Average compressive pressure uses its normal component and is a scalar.
✎ PRACTICE — Independent Surface-Pressure Cases
DOK 1–3 — PracticeChallenge 1: A Four-Block Stack
Four identical blocks each have weight 18.0 N. They form one vertical stack at rest. The lowest block contacts a level table over area 0.030 m². Find the stack’s average contact pressure on the table.
Step-by-Step Solution
Normal load = 4(18.0) = 72.0 N. Only the lowest block contacts the table over 0.030 m², so P = 72.0/0.030 = 2400 Pa.
Challenge 2: Three Possible Faces
A rectangular block has mass 9.0 kg and dimensions 0.10 m × 0.20 m × 0.30 m. It rests on a level table on any one of its three face types. Take g = 10 N/kg. Find the maximum and minimum average contact pressures.
Step-by-Step Solution
Weight = 9.0(10) = 90 N. Face areas are 0.020, 0.030 and 0.060 m². The smallest gives maximum P = 90/0.020 = 4500 Pa; the largest gives minimum P = 90/0.060 = 1500 Pa.
Challenge 3: Audit a Tilted-Force Report
A 100 N force acts on a horizontal plate at 60° to its downward normal. The rectangular contact face is 2.0 cm by 5.0 cm. Plate weight is negligible and a guide carries the tangential component. A report uses the full applied force for pressure, treats the numerical area in cm² as the same numerical area in m², and describes pressure as a downward vector. Find the contact area in m², normal force in N and average pressure in kPa. Explain all three errors.
Step-by-Step Solution
Area = 2.0 × 5.0 = 10 cm² = 0.0010 m². The angle is measured from the normal, so normal force = 100 cos 60° = 50 N. Pressure = 50/0.0010 = 50000 Pa = 50 kPa.
The full 100 N includes a tangential component carried by the guide. Squared units require 1 cm² = 10⁻⁴ m². Pressure is scalar; the normal contact force, rather than the pressure itself, has a downward direction on the supported surface.
☷ CHALLENGE — Sort Pressure, Geometry and Response
DOK 2 — ApplySort Pressure, Geometry and Response
Classify each statement by the physical idea it describes.
0 / 6 correct
Physics Insight
A correct pressure calculation and a valid material-response model are separate requirements.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Explain why the same perpendicular force produces more average pressure on a smaller contact area. Explain what changes for an angled applied force and why a pressure value alone does not predict how every material will deform.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 7.2 — Pressure
Use normal force and the actual contact area.
1. Average pressure
Paverage = Fnormal/A; uniform pressure: Fnormal = PA
Use actual contact area and the magnitude of force perpendicular to the surface. Pressure is scalar. Its associated surface force is a vector with a normal direction. If stress varies across a contact, Fnormal/A is the average, not necessarily the value at every point.
2. Angled forces
For angle θ measured from the surface normal, Fnormal = F cos θ. If the angle is instead measured from the surface, the perpendicular component uses sine. Read the given reference. The guide in the simulator carries the tangential component; that component does not add to average compressive pressure.
In the report case, 100 N at 60° to the normal supplies 50 N normal load. Its 2 cm by 5 cm face is 10 cm² = 0.001 m². Average pressure is 50000 Pa = 50 kPa. Calling pressure a downward vector confuses it with the normal force on the contact.
3. How area and force change the ratio
At fixed normal force, doubling area halves pressure. At fixed area, doubling normal force doubles pressure. Doubling both leaves the ratio unchanged. Stacking objects increases supported weight but does not multiply the bottom contact area. Reorienting one rectangular block changes area without changing its weight.
For the practice block, the supported load is 90 N. Face areas 0.020, 0.030 and 0.060 m² give different average pressures. The maximum is 4500 Pa and the minimum 1500 Pa.
4. Units
1 Pa = 1 N/m²; 1 kPa = 1000 Pa; 1 MPa = 10⁶ Pa
1 cm² = 10⁻⁴ m²; 1 mm² = 10⁻⁶ m²
Square the length conversion. A centimeter is 0.01 m, so a square centimeter is (0.01 m)². One standard atmosphere is defined as 101325 Pa; actual atmospheric pressure varies with altitude and weather. One bar is defined as 100000 Pa. These units do not imply air pressure is the same everywhere.
5. Fluid pressure and atmosphere
Fluid pressure arises from the collective interactions of particles with surfaces. An equilibrium fluid exerts normal forces on surfaces in different orientations. Pressure is not a force in newtons or the raw weight of everything above a point. In a static constant-density column, a height difference adds a pressure difference ρgΔh, with a reference boundary pressure. Later missions develop this distinction.
Air is compressible and its density varies with height. Atmospheric pressure cannot be inferred from a universal fixed-height slab of uniform air. This mission uses supplied or measured pressure values rather than unverified summit figures.
6. Deformation needs material information
A narrow contact can produce greater pressure for the same normal force, but deformation and failure depend on material properties, geometry and conditions. There is no universal pressure above which every material is cut. A bed of nails is not automatically safe; how load is shared and the actual tip geometry matter.
The simulator specifies an ideal elastic foundation with P = Kδ and K = 100000 Pa/m. This supplied model predicts its compression δ and elastic energy ½KAδ². It is not a general law for soil, skin, snow or wood. No damage or penetration is modeled.
7. The live pressure ramp
The force rises linearly for 2 physical seconds while angle and contact area stay fixed. The plate is massless and loading is quasi-static, so applied normal force balances the foundation response at every displayed state. Its visible vertical displacement equals the predicted compression. The square plate width scales with √A; vertical compression uses 400 pixels/m.
Eight real seconds show one physical run. Compare two areas, then force, with the other controls fixed. Pause, step and reset inspect the same model state. Three matched completed runs earn exploration credit; merely loading a preset does not.
8. Course scope
AP Physics 1 topic 8.2 covers normal force per area, scalar pressure and ideal-fluid pressure properties. Cambridge AS Level 9702 topic 4.3 defines and uses pressure. The explicitly supplied elastic foundation is an illustrative model, not an extra material law to memorize.
✓ Crest’s Checklist
- I identify the surface normal.
- I use the normal component of an angled force.
- I calculate the actual contact area.
- I square the unit-conversion factor for area.
- I distinguish scalar pressure from vector force.
- I state which quantity is fixed in proportional reasoning.
- I use a supplied material law before predicting deformation.
— Crest ☆ “Use normal force and the actual contact area.”
Mission 7.2 Complete! · All 10 levels cleared · PHYSICS CREST
★ Master of Pressure
A force is a vector. Average compressive pressure uses its normal component and is a scalar.