WONDER — The Mystery
A Ratio Can Test a Claim
An unknown liquid fills a small vial. A larger sample of the same uniform liquid, at the same temperature and pressure, has more mass and more volume. Why can those samples have the same density? Can a density measurement narrow the candidate list without uniquely proving the liquid’s identity?
Model: Density is mass per volume. Treat each liquid sample as uniform, with constant density during a run. Temperature, pressure and composition are fixed. The simulator supplies a known model density and generates ideal measurements; real measurements have uncertainty. Liquids and gases are fluids because they can flow and have no fixed shape. An ideal fluid is incompressible and has no viscosity; real gases are usually compressible.
PREDICT — Commit to Your Answer
DOK 2 — PredictThree uniform liquid samples have equal volumes of 250 mL. Their net masses are A: 180 g, B: 250 g and C: 325 g. Rank their densities from least to greatest.
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
The volume is the same for all three, so increasing net mass means increasing density. The order is A, B, C. This comparison depends on the equal-volume condition.
▶ PLAY — Live Filling Experiment on a Balance
DOK 2 — InvestigatePredict, measure and compare
Complete two runs with different target volumes but the same model density and flow rate. Then change only density from one of that pair. Measure three matched runs. Watch liquid flow into the graduated vessel while its level and gross balance reading rise. Compare net mass, volume and their ratio.
A uniform incompressible liquid enters a 500 mL vessel at the chosen constant volume flow rate. The vessel has a 50 g tare mass. Its gross balance reading includes that tare; its net liquid mass does not. The fill ends at the selected target volume, with duration = target volume divided by flow rate. Eight real seconds display one full physical run. The balance represents a quasi-static ideal mass measurement; pouring impact is ignored. At zero liquid volume, a measured density from net mass divided by volume is undefined. The known model density still sets the incoming liquid’s mass flow. No substance is identified solely from its density.
Status: Ready
Playback: 8 real seconds per run; read elapsed physical model time. Pause or Step for measurements.
Measured Net Mass vs Liquid Volume
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — The Ratio, the Measurement and the Units
DOK 1 — RecallFlip all 4 rule cards. Keep the quantities and model conditions clear.
Rule 1
Density and its rearrangements
Click to flip
Density and its rearrangements
ρ = m/V, m = ρV and V = m/ρ. Use the sample’s net mass and corresponding volume. Density is a property of the material under specified conditions, not a measure of sample amount.
Rule 2
Tare and displacement
Click to flip
Tare and displacement
Subtract the empty container’s mass from a gross reading. For a fully submerged insoluble nonporous solid, the rise in liquid volume gives solid volume if no bubbles or spills occur.
Rule 3
Cubic volume conversions
Click to flip
Cubic volume conversions
1 mL = 1 cm³ = 10⁻⁶ m³; 1 L = 10⁻³ m³. Therefore 1 g/mL = 1000 kg/m³. Cubing a length conversion is essential when converting volumes.
Rule 4
Conditions and identification
Click to flip
Conditions and identification
Density can change with temperature, pressure and composition. A measured density can support or reject candidates, but different materials or mixtures can share it; further evidence may be needed for unique identification.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “A larger sample of the same uniform liquid must be denser.”
Correct — the claim is false.
False at the same temperature, pressure and composition. Increasing sample amount increases mass and volume together. Their ratio stays constant. A change of conditions is a separate question.
Myth 2: “Matching a reference density uniquely proves a substance’s identity.”
Correct — the claim is false.
False. Density is useful evidence, but candidate ranges can overlap and distinct substances or mixtures can share a density. Measurement uncertainty and conditions matter; use another distinguishing test when needed.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Net Mass, Sample Volume and Conversions
DOK 2 — ApplyUse the sample’s own mass and volume. Treat reference values as given approximations under stated conditions.
Instructor Q1 — Find the Mass
A uniform sample has known density and volume. Which expression gives its net mass?
Instructor Q2 — A Gross Balance Reading
Which reading belongs in a liquid’s density calculation when a vessel sits on the balance?
Instructor Q3 — A Fresh Density
A uniform sample has net mass 156 g and volume 120 mL. Find its density in g/mL.
Instructor Q4 — Convert a Density
A density is 0.85 g/cm³. Express it in kg/m³.
4/4 — Instructor Questions Completed
At fixed conditions, scaling a uniform sample scales both net mass and volume together. Their ratio stays constant.
✎ PRACTICE — Independent Density Measurements
DOK 1–3 — PracticeChallenge 1: A Liquid Sample
A uniform liquid has density 0.840 g/mL at the stated conditions. A sample occupies 150 mL. Find its net mass in grams.
Step-by-Step Solution
Net mass = density × volume = 0.840 × 150 = 126 g.
Challenge 2: An Irregular Solid
An insoluble nonporous solid has mass 192 g. A graduated cylinder initially reads 40.0 mL and reads 65.0 mL after the solid is fully submerged, with no bubbles or spills. Find the solid’s volume in cm³ and its density in kg/m³.
Step-by-Step Solution
Solid volume = 65.0 − 40.0 = 25.0 mL = 25.0 cm³. Density = 192/25.0 = 7.68 g/cm³ = 7680 kg/m³. The final cylinder reading includes the original liquid; it is not the solid volume alone.
Challenge 3: Audit a Liquid-Identification Report
An empty vessel has mass 54.0 g. With 120 mL of an unknown liquid, its gross mass is 198 g. At the same conditions, candidate A has a reference density range 1.16–1.24 g/mL and candidate B has range 1.18–1.22 g/mL. A report divides the gross mass by liquid volume, labels the resulting g/mL number directly as kg/m³, and claims that density uniquely identifies the liquid. Find the liquid’s net mass and correct density in both units. Explain all three errors and say what the candidate evidence supports.
Step-by-Step Solution
Net mass = 198 − 54.0 = 144 g. Density = 144/120 = 1.20 g/mL = 1200 kg/m³.
The vessel’s tare must be removed; gross mass overstates liquid mass. A g/mL value must be multiplied by 1000 to express it in kg/m³. The correct density lies in both candidate ranges, so both remain consistent with this measurement. Density alone does not uniquely identify the liquid; another distinguishing measurement is required, at controlled conditions.
☷ CHALLENGE — Sort the Measurements and the Interpretation
DOK 2 — ApplySort the Measurements and the Interpretation
Classify each statement by the main step it supports.
0 / 6 correct
Physics Insight
A correct ratio is useful evidence; it does not automatically give a unique material identity.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: Explain why doubling the amount of a uniform liquid at fixed conditions doubles its mass and volume but leaves density unchanged. Explain why a vessel’s tare is removed and why density alone may not identify an unknown liquid.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 7.1 — Density
Measure net mass. Measure volume. Compare the ratio.
1. What density measures
ρ = m/V; m = ρV; V = m/ρ
Use the net mass and corresponding volume of the selected sample. Mass is measured in kg and volume in m³ for SI density in kg/m³. Density is mass per volume; it is not weight, mass alone or an amount of material. A uniform sample has one density at specified temperature, pressure and composition.
2. Same material, same conditions
Doubling a uniform sample’s volume doubles its mass at fixed conditions, so the ratio is unchanged. A larger sample need not be denser. Equal masses can occupy different volumes and therefore have different densities. Equal volumes can have different masses and therefore different densities.
Density can vary with temperature and pressure. Liquids and solids usually expand on warming, reducing density if mass is fixed. Gases can change density strongly with pressure and temperature. Water near ordinary room conditions is approximately 1000 kg/m³; this is a useful approximation, not an exact universal constant.
3. The liquid’s mass, not the container’s
Net liquid mass = gross mass − empty-vessel tare mass. If the balance has been correctly tared with the empty vessel, its displayed reading is already net mass. Do not subtract the tare twice. The simulator uses a fixed 50 g vessel and labels both gross and net readings.
Read a graduated cylinder at eye level using the appropriate meniscus; avoid parallax. Use the same vessel and sufficient resolution. The ideal simulation has exact readings; real apparatus has uncertainty. A balance measures mass; calling a mass in kilograms a weight confuses it with gravitational force in newtons.
4. A solid’s displaced volume
For an insoluble nonporous solid fully submerged without bubbles or spills, solid volume equals final minus initial liquid volume. The final reading includes the original liquid. A porous or dissolving object, trapped gas or partial submersion changes the method’s validity.
For the practice solid, volume = 65.0 − 40.0 = 25.0 cm³. With mass 192 g, density is 7.68 g/cm³ = 7680 kg/m³. A hollow sealed object’s average density uses its total mass divided by its external displaced volume; that need not equal its wall material’s density.
5. Cubic units
1 mL = 1 cm³ = 10⁻⁶ m³; 1 L = 10⁻³ m³
1 g/mL = 1 g/cm³ = 1000 kg/m³
One meter is 100 centimeters, so one cubic meter is one million cubic centimeters. Convert both mass and volume: 1 g = 0.001 kg and 1 cm³ = 0.000001 m³. The density conversion factor follows from their ratio. Never reuse the linear factor for cubic volume.
6. Density does not uniquely identify every substance
Density can support or reject a candidate when reference conditions and measurement uncertainty are comparable. Different materials and mixtures can share a density. Candidate ranges may overlap; another physical or chemical measurement may be required for unique identification.
In the audited report, net mass is 144 g and density is 1.20 g/mL = 1200 kg/m³. This fits both supplied candidate ranges. The report fails to subtract tare, changes the unit label without conversion, and claims more certainty than the evidence supports. No reference-density table needs to be memorized; use supplied values and stated conditions.
7. Fluids and the live filling model
Liquids and gases can flow and have no fixed shape. Their behavior stems from interactions between constituent particles. An ideal fluid is incompressible and has no viscosity. Real air is not generally incompressible, although a constant-density approximation can work for a specified situation.
The incoming model liquid has fixed density ρ. At constant volume flow rate Q, accumulated volume is Qt until the target is reached, and net mass is ρQt. The vessel level, flowing stream and balance readings change with the same physical time. The net-mass-versus-volume line has slope ρ. At the empty start, net m/V is 0/0 and is undefined; the incoming model’s known density still exists.
Eight real seconds display the complete physical interval; physical fill duration is target volume divided by Q. Run, pause, step and reset inspect the same state. Compare two sample volumes, then model density, with other controls fixed. Three matched completed runs unlock the next stage; preset loading alone earns no credit.
8. Course scope
AP Physics 1 topic 8.1 covers fluid properties, density and ideal-fluid assumptions. Cambridge AS Level 9702 topic 4.3 defines and uses density. Density measurement and unit reasoning support those topics. Floating and buoyant-force decisions are developed later in Chapter 7.
✓ Crest’s Checklist
- I use the sample’s net mass.
- I measure the corresponding sample volume.
- I subtract displacement readings for a submerged solid.
- I cube length conversions when converting volume.
- I compare samples at specified conditions.
- I distinguish bulk average density from material density.
- I treat density as evidence rather than a unique fingerprint.
- I distinguish mass in kg from weight in N.
— Crest ☆ “Measure net mass. Measure volume. Compare the ratio.”
Mission 7.1 Complete! · All 10 levels cleared · PHYSICS CREST
★ Master of Density
At fixed conditions, scaling a uniform sample scales both net mass and volume together. Their ratio stays constant.