WONDER — The Mystery
The Easy-Pull Question
A suitcase’s mass and weight stay the same when you angle the handle upward. How does the upward component change the floor’s support and sliding friction? Does that mean every steeper angle gives a larger forward net force?
Model: Right-sliding contact on a horizontal floor with a specified angled force and kinetic coefficient. Uniform g = 9.8 m/s²; +x right and +y up. While contact is maintained, vertical acceleration is zero. Coefficient calculations follow AP; AS friction remains qualitative.
PREDICT — Commit to Your Answer
DOK 2 — PredictA box stays in contact with the floor with zero vertical acceleration. A nonzero upward component of the pull helps support its unchanged weight. What happens to normal force compared with a horizontal pull?
Commit to both a prediction and a reason before revealing the explanation.
Step 1: Pick your answer.
STOP! Before revealing — why did you pick that?
Correct prediction and reasoning saved.
Vertical force balance gives N + Fᵧ − mg = 0, so the upward component reduces N. Weight and mass are unchanged.
▶ PLAY — Angled Pull and Push — Contact Snapshot
DOK 2 — InvestigatePredict, measure and compare
Compare the same force and mass at two angles. Then change only mass from one of that pair. Observe three matched setups. Positive angle pulls up; negative angle pushes down.
Instantaneous force snapshots of a box sliding right. μₖ = 0.3. While supported, N + Fᵧ = mg. If the upward applied component exceeds weight, N = 0, friction = 0 and the snapshot has upward acceleration. This lab does not animate later airborne motion.
Status: Ready
Playback: 1 simulation seconds per real second. Pause or Step for measurements.
Measurements
Load givens — then predict and run
Loading a setup earns no trial credit.
♢ DISCOVER — Rules of Angled Forces
DOK 1 — RecallFlip all 3 rule cards. Keep the quantities and model conditions clear.
Rule 1
Resolve the applied force
Click to flip
Resolve the applied force
For a signed angle θ above +x, Fₓ = F cos θ and Fᵧ = F sin θ. A negative θ has a downward vertical component. Draw the actual angled force; its components belong in the calculation, not as extra forces.
Rule 2
Check floor support
Click to flip
Check floor support
For maintained contact and zero vertical acceleration, N = mg − Fᵧ. A downward component increases N. If this relation would require N < 0, the floor cannot pull downward: contact is lost and use N = 0 with nonzero vertical acceleration.
Rule 3
Calculate friction and net force
Click to flip
Calculate friction and net force
For right-sliding contact, friction is −μₖN and ΣFₓ = F cos θ − μₖN. Tilting up reduces N but also changes the forward component. A steeper angle is not automatically better; state which quantity is being compared.
All rules explored.
MISCONCEPTION ATTACK — Destroy the Myths
DOK 2 — AnalyzeChoose TRUE or FALSE for each claim. The explanation appears after an attempt; only a correct answer completes the claim.
Myth 1: “Normal force always equals weight.”
Correct — the claim is false.
False. An upward applied component reduces floor support; a downward component increases it, provided contact is maintained. On an incline the normal direction also differs from vertical.
Myth 2: “For an angled pull at constant straight-line velocity, the total applied-force magnitude equals friction.”
Correct — the claim is false.
False in general. With no other horizontal forces, the horizontal component F cos θ balances friction. The total applied magnitude equals it only for the horizontal special case.
Both myths corrected. Continue to the instructor questions.
✦ THE SECOND “AHA!” — Pull Up or Push Down
DOK 2 — ApplyKeep actual forces and their calculated components distinct. Apply contact conditions before a friction equation.
Instructor Q1 — Downward Push
A downward angled push acts on a box that remains on a horizontal floor. What happens to normal force compared with the same horizontal push magnitude?
Instructor Q2 — Steady Tow
For constant straight-line horizontal velocity under an angled rope and friction, which rope quantity balances friction?
Instructor Q3 — Vertical Component
A 120 N force acts 30° above the horizontal. Find its signed vertical component, taking upward positive.
Instructor Q4 — Normal Force
A 20 kg box remains supported on a floor with zero vertical acceleration. A 60 N upward applied component acts. Use g = 9.8 m/s². Find N.
4/4 — Instructor Questions Completed
Vertical force balance changes normal force; horizontal acceleration still uses the resolved forward component.
✎ PRACTICE — Components and Floor Support
DOK 1–3 — PracticeChallenge 1: The Angled Suitcase
A 24 kg suitcase remains on a horizontal floor with zero vertical acceleration. It is pulled with 140 N at 28° above horizontal. Use g = 9.8 m/s² and upward positive. Find the signed vertical component of the pull and normal force.
Step-by-Step Solution
Fᵧ = 140 sin 28° ≈ +65.726 N. N = 235.2 − 65.726 ≈ 169.474 N.
Challenge 2: The Constant-Velocity Tow
A 90 kg snowmobile moves at constant velocity along a straight horizontal surface. A 360 N rope pulls 18° above horizontal. The only horizontal forces are the rope and sliding friction; contact is maintained. Find the friction magnitude.
Step-by-Step Solution
Zero horizontal acceleration gives friction = F cos θ = 360 cos 18° ≈ 342.38 N.
Challenge 3: Audit the Angled-Pull Report
A 15 kg box is sliding right on a horizontal floor while a 90 N force pulls 40° above horizontal. Contact is maintained. μₛ = 0.40, μₖ = 0.25, g = 9.8 m/s² and +x is right. A student reports: (i) normal force is mg, unaffected by the rope; (ii) sliding friction is μₛN; (iii) horizontal net force is the total 90 N pull minus friction. Calculate normal force, friction magnitude and signed horizontal acceleration. Explain all three errors.
Step-by-Step Solution
Vertical support: Fᵧ ≈ 57.851 N, so N ≈ 89.149 N.
Sliding contact: use μₖ, giving friction ≈ 22.287 N left.
Horizontal component: Fₓ ≈ 68.944 N. Thus net force ≈ +46.657 N and aₓ ≈ +3.110 m/s². The total 90 N magnitude is not the horizontal component.
☷ CHALLENGE — Rank the Signed Net Force
DOK 2 — ApplyRank the Signed Net Force
A 50 kg box already slides right on a horizontal floor. An applied force has fixed magnitude 100 N and μₖ = 0.4. Contact remains at all listed angles. Rank the signed horizontal net force from least to greatest. All four net forces are leftward; “best” here means least deceleration, not a forward net force.
0 / 6 correct
Physics Insight
At fixed F and maintained contact, the best angle for horizontal net force balances reduced friction against reduced horizontal pull. This is not a general claim about energy efficiency.
TEACH — The Feynman Technique
DOK 3 — TeachYour Final Mission: A sibling pushes down on a lawnmower handle and asks why it can resist motion more than an upward-pulled wagon. Explain how the vertical component changes normal force and kinetic friction, and why the horizontal component also matters.
Use simple words and at least three short sentences. This checks effort; compare your physics with the Vault or your teacher.
Type Your Explanation (≥ 3 sentences)
Draw a labelled explanation with at least three purposeful strokes. This checks effort; compare your physics with the Vault or your teacher.
Cyan pen selected.
Final reward below
Hidden exam secrets inside — Crest's private notebook.
Crest’s Secret Notebook
Mission 3.16 — Angled Forces
Resolve the force. Check the contact.
1. Resolve using the stated angle
Take +x right and +y up. For signed angle θ measured above +x:
Fₓ = F cos θ; Fᵧ = F sin θ
Positive θ gives an upward component. Negative θ gives a downward component. Mass and weight do not change when the force tilts.
2. Normal force is a response
While contact is maintained with zero vertical acceleration, N + Fᵧ − mg = 0, hence N = mg − Fᵧ. An upward component reduces N; a downward component increases it. Normal force is perpendicular to the contact surface.
Example: mass 18 kg and a 110 N pull at 25° give upward component about 46.488 N and N ≈ 129.912 N. With μₖ = 0.20, right-sliding friction has magnitude about 25.982 N.
3. Check loss of contact
The floor cannot supply a tensile downward normal force. If the supported-contact calculation gives a negative N, it is invalid: use N = 0 and floor friction zero. With the applied vector maintained at that instant, vertical net force is Fᵧ − mg and aᵧ = (Fᵧ − mg)/m upward.
At Fᵧ = mg, contact is at its zero-normal-force boundary. Later motion depends on the continuing force and geometry. The lab displays an instantaneous force snapshot; it does not calculate a later airborne trajectory.
4. Horizontal dynamics
For right-sliding contact, friction acts left with magnitude μₖN. Horizontal net force is F cos θ − μₖN, and aₓ is that force divided by mass. A downward push may increase N and friction, while its forward component still contributes to motion.
Draw the actual angled force, weight, normal and friction on a free-body diagram. Resolve the angled force separately. Adding the force and its components as separate interactions would count it twice.
5. Constant velocity has a direction condition
Constant straight-line velocity means zero acceleration. With only the rope and friction horizontally, F cos θ equals friction. Constant speed alone is insufficient if direction changes, as in circular motion. This mission’s steady-tow questions state a straight horizontal path.
6. A steeper pull is not always better
While contact remains, increasing upward angle reduces normal force and friction, but also reduces the horizontal pull component. At fixed force magnitude, horizontal net force is F(cos θ + μₖ sin θ) − μₖmg.
Its interior maximum occurs at tan θ = μₖ if that angle is reachable and contact remains. This compares horizontal net force in a particular ideal model; it does not establish a universal optimum for starting motion, energy use or real transport.
An upward force component on a body with no vertical displacement does no vertical work. Calling it “energy wasted lifting” while the body stays on the floor would be misleading.
7. Read the contact lab
Positive angle pulls up and negative angle pushes down. The model starts with rightward sliding, so kinetic friction applies while supported. Adjust force, angle and mass. The readouts list calculated components, while arrows show actual forces using one common force scale.
Observe a matched angle pair and a mass comparison. The one-second observation interval records the force setup; it is not an integration of subsequent motion. At loss of contact, the vertical-acceleration readout changes rather than incorrectly keeping vertical equilibrium.
Coefficient calculations follow AP Physics 1. The AS syllabus covers force resolution, net force and qualitative friction; it does not require coefficient treatment.
✓ Crest’s Checklist
- I state the angle reference and positive axes.
- I resolve the applied force without double-counting it.
- I check vertical balance and maintained contact.
- I use the horizontal component for horizontal motion.
- I distinguish constant speed from constant velocity.
- I qualify any optimum-angle statement.
— Crest ☆ “Resolve the force. Check the contact.”
Mission 3.16 Complete! · All 10 levels cleared · PHYSICS CREST
★ Master of Angled Forces
Vertical force balance changes normal force; horizontal acceleration still uses the resolved forward component.