Skip to lesson
1

Topic 9 · Electricity

Gravity in calculations: use g = 9.81 m/s² (9.81 N/kg) near Earth, unless the question or activity supplies a different value. Keep the supplied value throughout the calculation.

Topic map
This chapter is organised around three connected ideas: charge moving as current, energy transferred per unit charge, and how materials oppose current. Learn the definitions precisely, then practise switching between equations, graphs and physical explanations.

9.1 · Electric current

  • CurrentCharge flow per time.
  • Potential differenceEnergy transferred per charge.
  • ResistanceV/I at an operating point.
  • These meanings explain meter connections and prevent charge from being confused with energy.
Current and charge
An electric current is a flow of charge carriers. For a steady current, $$\boxed{Q=It}\qquad\text{and}\qquad\boxed{I=\frac{Q}{t}}$$ where $Q$ is charge in coulombs, $I$ is current in amperes and $t$ is time in seconds.

Unit meaning: $1\,\mathrm{A}=1\,\mathrm{C\,s^{-1}}$.

Quantised charge
Charge comes in discrete packets. The magnitude of the elementary charge is $$\boxed{e=1.60\times10^{-19}\,\mathrm C}$$ so a charge made from whole elementary charges satisfies $$\boxed{Q=Ne}$$ where $N$ is an integer. In a metal the mobile carriers are electrons; in electrolytes both positive and negative ions can carry charge.
Direction trap
Conventional current is defined in the direction positive charge would move. Electrons in a metal drift in the opposite direction.
tI

Current–time graphs

For a changing current, charge is the area under the $I$–$t$ graph: $$\boxed{Q=\text{area under the }I\text{–}t\text{ graph}}$$ You do not need calculus for straight-line sections: split the area into rectangles, triangles or trapezia. For a linear change from $I_1$ to $I_2$, $$Q=\frac{I_1+I_2}{2}\,t.$$
Common mistakes
  • Using minutes or hours without converting to seconds.
  • Using mA as though it were A.
  • Counting a non-integer number of elementary charges in a quantisation question.
Quick check
A current falls uniformly from $0.30\,\mathrm A$ to $0.10\,\mathrm A$ in $5.0\,\mathrm s$. Find the charge transferred.
$Q=\frac{0.30+0.10}{2}\times5.0=1.0\,\mathrm C$.
2

9.1 · Drift model

From moving carriers to $I=Anvq$

  • In a wire, I = nAqv links current to carrier density, cross-section, carrier charge and drift speed.
  • Resistance depends on material and geometry; a component’s temperature can change its resistance during a measurement.
−−−−−−−− conventional current I electron drift velocity v area A

Consider a conductor with cross-sectional area $A$. The number density $n$ is the number of mobile charge carriers per unit volume. Each carrier has charge magnitude $q$ and mean drift speed $v$.

Derivation
In time $t$ the carriers drift a distance $vt$. The volume that passes a cross-section is $Avt$, so the number of carriers is $nAvt$. Therefore the charge passing is $$Q=nAvtq.$$ Dividing by time gives $$\boxed{I=Anvq}.$$ For electrons, use $q=e$ as the magnitude of the carrier charge when calculating current magnitude.
Same current, thinner wire
$v=I/(Anq)$, so smaller $A$ means larger drift speed.
Diameter trap
$A=\pi d^2/4$. Doubling diameter makes area four times larger.
Same wire
If $n,A,q$ are unchanged, $I\propto v$.
Number density
Unit: $\mathrm{m^{-3}}$. Keep powers of ten under control.
Build the formula instead of memorising it
Think area × distance = volume, then volume × number density = number of carriers, then number × charge = charge, then divide by time.
Quick check
A wire carries the same current after its diameter is halved. Assume $n$ is unchanged. By what factor does drift speed change?
Diameter halves $\Rightarrow A$ becomes $1/4$. Since $v=I/(Anq)$, the drift speed becomes 4 times larger.
3

9.2 · Potential difference & power

9.2 · Potential difference

Energy transferred per unit charge
The potential difference across a component is the energy transferred per unit charge: $$\boxed{V=\frac{W}{Q}}$$ where $W$ is energy transferred in joules. Hence $1\,\mathrm V=1\,\mathrm{J\,C^{-1}}$ and $W=VQ$.
Q componentV energyW = VQ

Potential difference tells you how much energy is transferred for each coulomb of charge passing through the component.

Combine $W=VQ$ with $Q=It$ to obtain $W=VIt$ when $V$ and $I$ are constant.

Electrical power

Three useful forms
Power is the rate of energy transfer. Using $P=W/t$, $W=VQ$ and $Q=It$ gives $$\boxed{P=VI}.$$ For a component with resistance $R$, combine this with $V=IR$: $$\boxed{P=I^2R}\qquad\boxed{P=\frac{V^2}{R}}.$$ All three are equivalent when the quantities refer to the same component at the same operating point.
Choosing the fastest equation
  • Know $V$ and $I$ → use $P=VI$.
  • Know $I$ and $R$ → use $P=I^2R$.
  • Know $V$ and $R$ → use $P=V^2/R$.
Scaling traps
For a constant resistance, doubling $V$ makes power four times larger because $P\propto V^2$. Doubling $I$ also makes power four times larger because $P\propto I^2$.
Quick check
A $12\,\Omega$ resistor is connected across $6.0\,\mathrm V$. Find the power and the energy transferred in $2.0\,\mathrm{min}$.
$P=V^2/R=36/12=3.0\,\mathrm W$. Time $=120\,\mathrm s$, so $W=Pt=360\,\mathrm J$.
Which quantity is potential difference?

4

9.3 · Resistance & Ohm’s law

9.3 · Resistance

Definition
The resistance of a component at an operating point is $$\boxed{R=\frac{V}{I}}$$ with unit ohm ($\Omega$), where $1\,\Omega=1\,\mathrm{V\,A^{-1}}$.
Ohm's law
For a conductor at constant physical conditions, the current through it is directly proportional to the potential difference across it: $$\boxed{V\propto I}.$$ Constant temperature is usually the key condition in exam questions.
VIgradient = I/V = 1/R

Read the axes before using a gradient

If the graph is $I$ vertically against $V$ horizontally, a straight ohmic line has gradient $I/V=1/R$.

If the axes are reversed ($V$ against $I$), the gradient is $R$.

Non-linear graph trap
At a point on a curved $I$–$V$ graph, the resistance is still $R=V/I$ using the coordinates of that point. Do not automatically use the tangent gradient as $R$.
Quick check
An $I$–$V$ graph has a straight-line gradient of $0.25\,\mathrm{A\,V^{-1}}$. Find the resistance.
For $I$ against $V$, gradient $=1/R$. Therefore $R=1/0.25=4.0\,\Omega$.
Your turn · Find resistance for V = 8.0 V and I = 0.20 A.

Decimals, scientific notation and compatible units are accepted. Keep any required sign.

5

9.3 · I–V characteristics

Three required characteristics

I–V characteristics · read both axesI–V characteristics · read both axesVImetal, fixed TVIfilament lampVIdiode
ComponentWhat the graph tells youPhysics
Metallic conductor at constant temperatureStraight line through origin; same gradient$R$ is constant, so it obeys Ohm's law.
Filament lampCurve becomes less steep as $|V|$ and $|I|$ increaseHigher current heats the filament. Greater lattice vibration causes more electron collisions, so resistance increases.
Semiconductor diodeVery small current for one polarity; rapid increase in current for the conducting polarityIt conducts strongly in one direction and blocks current in the other over the normal operating range.
Operating-point resistance
Suppose a filament lamp has $V=6.0\,\mathrm V$ and $I=0.30\,\mathrm A$ at one point. Then $$R=\frac{6.0}{0.30}=20\,\Omega.$$ At another point, read the new $V$ and $I$ and calculate $V/I$ again.
Avoid a false fixed-voltage rule for diodes
For this topic, learn the shape and directional behaviour of the diode characteristic. Do not treat one particular forward-voltage value as a universal constant unless a question gives that information.
Quick check
A lamp has $I=0.20\,\mathrm A$ at $V=2.0\,\mathrm V$ and $I=0.32\,\mathrm A$ at $V=4.0\,\mathrm V$. Show that its resistance has increased.
At $2.0\,\mathrm V$, $R=10\,\Omega$. At $4.0\,\mathrm V$, $R=12.5\,\Omega$. The resistance has increased as the filament has heated.
6

9.3 · Resistivity

Material + geometry

Resistivity equation
For a uniform wire, $$\boxed{R=\frac{\rho L}{A}}\qquad\text{or}\qquad\boxed{\rho=\frac{RA}{L}}$$ where $\rho$ is resistivity in $\Omega\,\mathrm m$, $L$ is length and $A$ is cross-sectional area.
length L dA = πd²/4

Circular wire

$$A=\pi r^2=\frac{\pi d^2}{4}.$$ For the same material and temperature, $$\boxed{R\propto\frac{L}{d^2}}.$$ This single proportionality solves many ratio questions.
Length doubles
Same area → $R$ doubles.
Diameter doubles
Area ×4 → $R$ becomes $R/4$.
Length ×2, diameter ÷2
$R$ changes by $2/(1/2)^2=8$.
Constant volume stretch
If $L$ increases, $A$ must decrease too, so resistance rises faster than length alone suggests.
LRgradient = ρ/A

Graph technique

For a wire of fixed area,

$$R=\frac{\rho}{A}L.$$

So a graph of $R$ against $L$ has gradient $\rho/A$. A non-zero intercept can indicate lead/contact resistance.

Unit traps
  • $1\,\mathrm{mm}^2=10^{-6}\,\mathrm{m}^2$.
  • If diameter is given, halve it before using $\pi r^2$.
  • Resistivity is a material property; resistance also depends on dimensions.
7

9.3 · Sensors & exam toolbox

LDR and NTC thermistor

LDRlight intensityR NTC thermistortemperatureR

LDR: increasing light intensity causes resistance to decrease.

NTC thermistor: increasing temperature causes resistance to decrease.

The syllabus requires these resistance trends. The detailed use of these components in potential-divider circuits belongs with D.C. circuits.

Master equation sheet
IdeaEquation / relationshipHigh-value check
Charge & current$Q=It$Area under $I$–$t$ gives $Q$
Quantisation$Q=Ne$$N$ is an integer
Drift current$I=Anvq$$A$ in $\mathrm m^2$, $n$ in $\mathrm{m^{-3}}$
Potential difference$V=W/Q$$1\,\mathrm V=1\,\mathrm{J/C}$
Power$P=VI=I^2R=V^2/R$All values must refer to same component
Resistance$R=V/I$Use operating-point coordinates on curved graphs
Ohm's law$V\propto I$Physical conditions constant
Resistivity$R=\rho L/A$$A=\pi d^2/4$ for round wire
Resistivity practical thinking
Measure the wire length $L$, diameter $d$ and resistance $R=V/I$. Repeat diameter measurements at several positions and orientations, average them, and keep the wire temperature as constant as possible. A graph of $R$ against $L$ is stronger than relying on one reading because its gradient can be used to obtain $\rho$.
Graph first
Check axes before interpreting gradient.
Geometry first
Convert diameter to area before resistivity calculations.
Explain physically
For a lamp, link current → temperature → lattice vibration → collisions → resistance.
Check dimensions
A plausible resistance cannot rescue an area conversion error.
Keep the next topic separate
The following are deliberately not treated as Topic 9 core here: e.m.f. and internal resistance, Kirchhoff's laws, combining resistors, potential dividers and potentiometers. They are developed in Topic 10 D.C. circuits.