Skip to lesson
P1

Topic 6 Practice · Deformation of Solids

Gravity in calculations: use g = 9.81 m/s² (9.81 N/kg) near Earth, unless the question or activity supplies a different value. Keep the supplied value throughout the calculation.

How to use this: These questions are original, but the techniques come from the current Topic 6 outcomes and recurring Cambridge-style patterns: natural length versus extension, diameter-squared scaling, graph gradients, Young modulus experiments, elastic/plastic reasoning, connected specimens and force–extension areas. Try each question before revealing the feedback.

MCQs · 1–10

Q1 Easy6.1 · Hooke
A spring extends by $6.0\,\mathrm{cm}$ when a load of $18\,\mathrm N$ is applied. What is its spring constant?
F = 18 Nextension = 6.0 cm
$x=0.060\,\mathrm m$, so $k=F/x=18/0.060=300\,\mathrm{N\,m^{-1}}$.
Q2 Medium6.1 · extension
A spring has natural length $25\,\mathrm{cm}$. A $12\,\mathrm N$ load increases its length to $31\,\mathrm{cm}$. What is $k$?
natural length 25 cmloaded length 31 cm
The extension is $31-25=6\,\mathrm{cm}=0.060\,\mathrm m$, so $k=12/0.060=200\,\mathrm{N\,m^{-1}}$.
Q3 Easy6.1 · compression
A spring of constant $250\,\mathrm{N\,m^{-1}}$ is compressed by $3.2\,\mathrm{cm}$. What is the magnitude of the compressive force?
k = 250 N m⁻¹compression = 3.2 cm
$F=kx=(250)(0.032)=8.0\,\mathrm N$.
Q4 Medium6.1 · graph
The force–extension graph is straight from O to P and then curves from P to Q. What does P identify?
PQxF
P is where the straight proportional relation ends, so it is the limit of proportionality. The elastic limit is a different idea.
Q5 Easy6.1 · stress
A wire of cross-sectional area $1.5\times10^{-6}\,\mathrm{m^2}$ carries a tensile load of $90\,\mathrm N$. What is its stress?
F = 90 NA = 1.5 × 10⁻⁶ m²
$\sigma=F/A=90/(1.5\times10^{-6})=6.0\times10^7\,\mathrm{Pa}$.
Q6 Medium6.1 · diameter
The diameter of a wire is doubled while the tensile force is unchanged. What happens to the stress?
d2dsame tensile forcesame tensile forcecompare d and 2d
$A\propto d^2$, so doubling $d$ makes $A$ four times larger. Since $\sigma=F/A$, stress becomes $1/4$.
Q7 Easy6.1 · strain
A $2.0\,\mathrm m$ wire extends by $1.6\,\mathrm{mm}$. What is its tensile strain?
original length 2.0 mextension 1.6 mm
$\varepsilon=x/L=(1.6\times10^{-3})/2.0=8.0\times10^{-4}$.
Q8 Medium6.1 · percentage strain
A rod of original length $1.20\,\mathrm m$ has a tensile strain of $0.35\%$. What is its extension?
original length 1.20 mstrain = 0.35%
$0.35\%=0.0035$, so $x=\varepsilon L=(0.0035)(1.20)=0.0042\,\mathrm m=4.2\,\mathrm{mm}$.
Q9 Hard6.1 · Young modulus
A wire has length $1.8\,\mathrm m$, diameter $0.50\,\mathrm{mm}$ and extension $2.0\,\mathrm{mm}$ under a force of $60\,\mathrm N$. What is its Young modulus?
L = 1.8 m · d = 0.50 mmF = 60 N · x = 2.0 mm
$A=\pi d^2/4=1.96\times10^{-7}\,\mathrm{m^2}$ and $E=FL/(Ax)\approx2.75\times10^{11}\,\mathrm{Pa}$.
Q10 Medium6.1 · stress–strain graph
In the proportional region of a stress–strain graph, a stress of $160\,\mathrm{MPa}$ produces a strain of $8.0\times10^{-4}$. What is the Young modulus?
stress = 160 MPastrain = 8.0 × 10⁻⁴
$E=\sigma/\varepsilon=(160\times10^6)/(8.0\times10^{-4})=2.0\times10^{11}\,\mathrm{Pa}$.
P2

MCQs · 11–20

Q11 Medium6.1 · $E$ vs $k$
Two wires are made of the same material but have different lengths and diameters. Which statement is correct while both obey Hooke's law?
same materialdifferent L and diameter
Young modulus is a property of the material. The specimen spring constant $k=EA/L$ depends on geometry.
Q12 Hard6.1 · scaling
A wire extends by $3.0\,\mathrm{mm}$ under a certain load. A second wire of the same material carries the same load but has three times the length and twice the diameter. What is its extension?
wire 1: L, dwire 2: 3L, 2dsame material · same load
$x\propto L/d^2$. The factor is $3/2^2=3/4$, so $x_2=(3/4)(3.0)=2.25\,\mathrm{mm}$.
Q13 Easy6.1 · material property
A Young modulus experiment is repeated using a wire of the same steel but twice the length and half the diameter. Assuming ideal measurements, what value of $E$ is obtained?
same steelL → 2L · d → d/2
The extension changes, but Young modulus is a property of the material, so the measured value remains $E$.
Q14 Medium6.1 · $k=EA/L$
A wire has spring constant $k$. Another wire of the same material has three times the cross-sectional area and twice the length. What is its spring constant?
same materialA → 3A · L → 2L
$k=EA/L$, so $k'=(3A)/(2L)\times E=(3/2)k$.
Q15 Hard6.1 · composite wire
Two wires X and Y of equal cross-sectional area are joined end-to-end and carry the same tension. X has length $1.0\,\mathrm m$ and Young modulus $2E$. Y has length $2.0\,\mathrm m$ and Young modulus $E$. X extends by $0.40\,\mathrm{mm}$. What is the total extension?
X: 1.0 m, 2EY: 2.0 m, Esame area and same tension
$x\propto L/E$. Relative to X, Y has factor $(2/E)/(1/2E)=4$, so $x_Y=1.6\,\mathrm{mm}$. Total $=0.40+1.60=2.0\,\mathrm{mm}$.
Q16 Medium6.1 · springs
Two identical springs, each of spring constant $120\,\mathrm{N\,m^{-1}}$, support a load symmetrically in parallel. What extension is produced by a total load of $24\,\mathrm N$?
24 N
The load is shared equally: each spring carries $12\,\mathrm N$. Hence $x=12/120=0.10\,\mathrm m$. Equivalently, $k_{\mathrm{eff}}=240\,\mathrm{N\,m^{-1}}$.
Q17 Medium6.2 · energy area
A spring obeys Hooke's law and reaches a force of $16\,\mathrm N$ at an extension of $5.0\,\mathrm{cm}$. What elastic potential energy is stored?
5.0 cm16 N
The area under the straight $F$–$x$ line is $\tfrac12Fx=\tfrac12(16)(0.050)=0.40\,\mathrm J$.
Q18 Hard6.2 · partial area
A spring of constant $400\,\mathrm{N\,m^{-1}}$ is already extended by $2.0\,\mathrm{cm}$. How much additional energy is stored when its extension increases to $5.0\,\mathrm{cm}$?
k = 400 N m⁻¹x: 2.0 cm → 5.0 cm
$\Delta E=\tfrac12k(x_2^2-x_1^2)=200(0.050^2-0.020^2)=0.42\,\mathrm J$.
Q19 Hard6.2 · non-linear graph
A non-linear force–extension curve starts at the origin, ends at $F=12\,\mathrm N$, $x=0.080\,\mathrm m$, and lies entirely below the straight line joining these endpoints. What can be said about the work done?
0.080 m12 N
The straight-line triangle would have area $\tfrac12(12)(0.080)=0.48\,\mathrm J$. The actual curve lies below that line, so its area and the work done are smaller.
Q20 Hard6.2 · energy scaling
Springs P and Q obey Hooke's law with $k_P=3k$ and $k_Q=k$. Each is stretched by the same force. What is $E_P:E_Q$?
same applied forceP: 3k · Q: k
For the same force, $E=F^2/(2k)$, so energy is inversely proportional to $k$. Hence $E_P:E_Q=1:3$.
P3

MCQs · 21–32

Q21 Medium6.2 · energy scaling
Two Hooke-law springs are stretched by the same extension. P has spring constant $2k$ and Q has spring constant $k$. What is $E_P:E_Q$?
same extensionP: 2k · Q: k
For the same extension, $E=\tfrac12kx^2$, so energy is directly proportional to $k$. Ratio $=2:1$.
Q22 Medium6.2 · compression energy
A spring of constant $600\,\mathrm{N\,m^{-1}}$ is compressed by $2.5\,\mathrm{cm}$. How much elastic potential energy is stored?
k = 600 N m⁻¹compression = 2.5 cm
$E=\tfrac12kx^2=\tfrac12(600)(0.025)^2=0.1875\,\mathrm J\approx0.188\,\mathrm J$.
Q23 Easy6.2 · definitions
Which statement correctly distinguishes elastic and plastic deformation?
loading / unloadingrecovery or permanent change?
Elasticity is about recovery after unloading. Plastic deformation leaves a permanent extension/compression.
Q24 Hard6.2 · proportional vs elastic
A material has a curved force–extension relation over part of its loading, but when the force is removed it returns exactly to zero extension. Which statement is correct?
loadingunloading
Returning to zero extension means the deformation is elastic. A curved loading graph means force is not proportional to extension throughout, so Hooke's law does not hold throughout.
Q25 Medium6.1 · experiment
Which set of measurements is sufficient to determine the Young modulus of a uniform wire under tension?
loadsextension scale
$E=FL/(Ax)$ requires $F$, original $L$, extension x and area $A$, which can be calculated from the measured diameter.
Q26 Medium6.1 · practical
Why is a relatively long wire useful in a Young modulus experiment?
same material and stressshort wire vs long wire
Since $x=FL/(EA)$, a longer wire gives a larger extension for the same $F,E,A$. A larger measured change normally has a smaller percentage uncertainty.
Q27 Medium6.1 · micrometer
Which is the best method for measuring the diameter of a wire for a Young modulus experiment?
Repeated micrometer readings detect non-uniformity and reduce random error. This matters strongly because $A\propto d^2$.
Q28 Hard6.1 · graph to $E$
The gradient of an $F$–$x$ graph for a wire is $8.0\times10^3\,\mathrm{N\,m^{-1}}$. The wire has length $1.5\,\mathrm m$ and diameter $0.60\,\mathrm{mm}$. What is its Young modulus?
L = 1.5 md = 0.60 mm
$E=kL/A$. Here $A=\pi(0.60\times10^{-3})^2/4=2.83\times10^{-7}\,\mathrm{m^2}$, so $E\approx4.24\times10^{10}\,\mathrm{Pa}$.
Q29 Medium6.1 · load
A $0.25\,\mathrm{kg}$ mass is hung from a spring of constant $98\,\mathrm{N\,m^{-1}}$. What extension is produced? Take $g=9.8\,\mathrm{m\,s^{-2}}$.
mass = 0.25 kgk = 98 N m⁻¹
The load is a force: $F=mg=(0.25)(9.8)=2.45\,\mathrm N$. Then $x=F/k=2.45/98=0.025\,\mathrm m=25\,\mathrm{mm}$.
Q30 HardTopic 5 + 6
A spring of constant $500\,\mathrm{N\,m^{-1}}$ is compressed by $4.0\,\mathrm{cm}$ and releases a $0.10\,\mathrm{kg}$ trolley on a frictionless track. What is the trolley's speed when all the spring energy has become kinetic energy?
k = 500 N m⁻¹ · x = 4.0 cm0.10 kg trolley
$E_s=\tfrac12(500)(0.040)^2=0.40\,\mathrm J$. With $\tfrac12mv^2=0.40$, $v=\sqrt8=2.83\,\mathrm{m\,s^{-1}}$.
Q31 Hard6.1 · reversed axes
A graph has extension $x$ on the vertical axis and force $F$ on the horizontal axis. In the proportional region its gradient is $2.5\times10^{-4}\,\mathrm{m\,N^{-1}}$. What is the spring constant?
force Fextension x
With $x$ vertical and $F$ horizontal, gradient $=x/F=1/k$. Hence $k=1/(2.5\times10^{-4})=4.0\times10^3\,\mathrm{N\,m^{-1}}$.
Q32 Hard6.2 · length vs extension
A spring has natural length $0.40\,\mathrm m$. Its tension increases linearly from zero to $10\,\mathrm N$ when its total length reaches $0.46\,\mathrm m$. How much elastic potential energy is stored?
force–length graphL₀ = 0.40 m · F = 10 N at 0.46 m
Energy uses the extension, not the total length. $x=0.46-0.40=0.060\,\mathrm m$, so $E_P=\tfrac12Fx=\tfrac12(10)(0.060)=0.30\,\mathrm J$.
S

Cambridge-style Structured Questions

Structured practice: work on paper first. Mark allocations are suggested for self-checking; the worked solutions show the method and physics that should appear in a strong answer.
S1 · Force–extension data 8 marks6.1 / 6.2
A spring is loaded gradually. The measurements are shown.
measured F–x dataproportional then slight deviation
$F/\mathrm N$0246810
$x/\mathrm{mm}$01.02.03.04.05.4

(a) Determine the spring constant using the proportional data. 2

(b) State the highest force in the table for which proportionality is supported, and explain your choice. 2

(c) Predict the extension at $7.0\,\mathrm N$ if the spring remains in the proportional region. 2

(d) Calculate the elastic potential energy stored at $8.0\,\mathrm N$. 2

(a) Using, for example, $F=8.0\,\mathrm N$, $x=4.0\times10^{-3}\,\mathrm m$: $k=F/x=2.0\times10^3\,\mathrm{N\,m^{-1}}$.

(b) $8.0\,\mathrm N$. Up to this point $F/x$ is constant. At $10\,\mathrm N$, proportionality would predict $5.0\,\mathrm{mm}$, not $5.4\,\mathrm{mm}$.

(c) $x=F/k=7.0/(2.0\times10^3)=3.5\times10^{-3}\,\mathrm m=3.5\,\mathrm{mm}$.

(d) $E_P=\tfrac12Fx=\tfrac12(8.0)(0.0040)=1.6\times10^{-2}\,\mathrm J$.
S2 · Young modulus experiment 12 marks6.1
A student determines the Young modulus of a metal wire of original length $1.80\,\mathrm m$ and mean diameter $0.40\,\mathrm{mm}$. In the proportional region, a $20.0\,\mathrm N$ increase in force produces an extension of $1.20\,\mathrm{mm}$.
loadscale

(a) Describe how the student should measure the wire diameter reliably. 3

(b) Calculate the cross-sectional area of the wire. 2

(c) Calculate the gradient of the $F$–$x$ graph. 2

(d) Determine the Young modulus. 3

(e) State two ways to improve the reliability/precision of the experiment. 2

(a) Use a micrometer screw gauge; take readings at several positions along the wire and in different orientations; calculate a mean diameter.

(b) $A=\pi d^2/4=\pi(4.0\times10^{-4})^2/4=1.26\times10^{-7}\,\mathrm{m^2}$.

(c) $k=\Delta F/\Delta x=20.0/(1.20\times10^{-3})=1.67\times10^4\,\mathrm{N\,m^{-1}}$.

(d) $E=kL/A=(1.67\times10^4)(1.80)/(1.26\times10^{-7})\approx2.39\times10^{11}\,\mathrm{Pa}$.

(e) Suitable points include: use a long wire to increase measured extension; take several load–extension points and use a best-fit gradient; repeat readings; measure diameter at more positions; use a sensitive extension scale/pointer; stay in the proportional region.
S3 · Composite wire 10 marks6.1
Two uniform wire sections X and Y, each of cross-sectional area $2.0\times10^{-7}\,\mathrm{m^2}$, are joined end-to-end and carry a tensile force of $40\,\mathrm N$. X has length $0.80\,\mathrm m$ and $E_X=2.0\times10^{11}\,\mathrm{Pa}$. Y has length $1.20\,\mathrm m$ and $E_Y=1.0\times10^{11}\,\mathrm{Pa}$.
X: 0.80 m, 2.0×10¹¹ PaY: 1.20 m, 1.0×10¹¹ Pa40 N tension

(a) Explain why the tensile force in X and Y is the same. 2

(b) Calculate the extension of X. 2

(c) Calculate the extension of Y. 2

(d) Find the total extension. 1

(e) Determine the effective spring constant of the complete joined wire. 2

(f) Explain which section contributes most to the total extension. 1

(a) The junction is in equilibrium, so the tension transmitted through the two series sections is the same (neglecting the junction's weight).

(b) $x_X=FL/(EA)=40(0.80)/[(2.0\times10^{11})(2.0\times10^{-7})]=8.0\times10^{-4}\,\mathrm m=0.80\,\mathrm{mm}$.

(c) $x_Y=40(1.20)/[(1.0\times10^{11})(2.0\times10^{-7})]=2.4\times10^{-3}\,\mathrm m=2.4\,\mathrm{mm}$.

(d) $x_{\mathrm{total}}=3.2\,\mathrm{mm}$.

(e) $k_{\mathrm{eff}}=F/x_{\mathrm{total}}=40/0.0032=1.25\times10^4\,\mathrm{N\,m^{-1}}$.

(f) Y extends more because it is longer and has the smaller Young modulus.
S4 · Plastic deformation and graph areas 10 marks6.2
A specimen is loaded from the origin to A at $x=3.0\,\mathrm{mm}$, $F=15\,\mathrm N$, then in a straight segment to B at $x=6.0\,\mathrm{mm}$, $F=24\,\mathrm N$. It is unloaded along a straight line from B to zero force at $x=1.5\,\mathrm{mm}$.
AB1.5 mmxF

(a) State what the non-zero intercept on the extension axis means physically. 2

(b) State whether the deformation at B is elastic or plastic. 1

(c) Calculate the work done during loading from O to B. 3

(d) Calculate the energy returned during unloading. 2

(e) Calculate the net energy not returned during the cycle. 2

(a) It is a permanent extension of $1.5\,\mathrm{mm}$ remaining when the force is removed.

(b) Plastic, because the specimen does not recover its original length.

(c) Area O→A $=\tfrac12(15)(0.003)=0.0225\,\mathrm J$. Area A→B is a trapezium: $[(15+24)/2](0.003)=0.0585\,\mathrm J$. Total input work $=0.081\,\mathrm J$.

(d) Unloading area is a triangle of base $6.0-1.5=4.5\,\mathrm{mm}$: $E_{\mathrm{returned}}=\tfrac12(24)(0.0045)=0.054\,\mathrm J$.

(e) Net energy not returned $=0.081-0.054=0.027\,\mathrm J$.
S5 · Compression 8 marks6.1 / 6.2
A uniform solid block of original length $0.50\,\mathrm m$ and cross-sectional area $4.0\times10^{-4}\,\mathrm{m^2}$ is compressed by two opposing forces of magnitude $12\,\mathrm{kN}$. Its length decreases by $0.30\,\mathrm{mm}$ and the deformation is proportional.
12 kN12 kN

(a) Calculate the compressive stress magnitude. 2

(b) Calculate the compressive strain magnitude. 2

(c) Determine the Young modulus. 2

(d) Calculate the elastic potential energy stored. 2

(a) $\sigma=F/A=1.20\times10^4/(4.0\times10^{-4})=3.0\times10^7\,\mathrm{Pa}$.

(b) $\varepsilon=x/L=(0.30\times10^{-3})/0.50=6.0\times10^{-4}$.

(c) $E=\sigma/\varepsilon=(3.0\times10^7)/(6.0\times10^{-4})=5.0\times10^{10}\,\mathrm{Pa}$.

(d) Because the deformation is proportional, $E_P=\tfrac12Fx=\tfrac12(1.20\times10^4)(0.30\times10^{-3})=1.8\,\mathrm J$.
S6 · Non-linear force–extension graph 8 marks6.2
A specimen has the following force–extension points, joined by straight lines.
piecewise F–x datawork = total graph area
$x/\mathrm m$00.0200.0500.080
$F/\mathrm N$03.09.018.0

(a) Calculate the work done in extending the specimen from $0$ to $0.080\,\mathrm m$. 4

(b) Calculate the work done only from $0.050\,\mathrm m$ to $0.080\,\mathrm m$. 2

(c) Explain why using $\tfrac12F_{\mathrm{final}}x_{\mathrm{final}}$ would not be valid for the whole loading. 2

(a) Add trapezium areas: $\tfrac12(0+3)(0.020)=0.030\,\mathrm J$; $\tfrac12(3+9)(0.030)=0.180\,\mathrm J$; $\tfrac12(9+18)(0.030)=0.405\,\mathrm J$. Total $=0.615\,\mathrm J$.

(b) The final trapezium area is $0.405\,\mathrm J$.

(c) $\tfrac12Fx$ assumes a straight line from the origin, i.e. force proportional to extension. Here the gradient changes, so the actual graph area must be used.
S7 · Two springs sharing a load 8 marks6.1 / 6.2
A $12.0\,\mathrm{kg}$ load hangs symmetrically from two identical vertical springs in parallel. Each spring has $k=1200\,\mathrm{N\,m^{-1}}$. Take $g=9.8\,\mathrm{m\,s^{-2}}$ and assume Hooke's law is obeyed.
12.0 kg

(a) Calculate the load carried by each spring. 2

(b) Calculate the common extension. 2

(c) Calculate the total elastic potential energy stored in the two springs. 2

(d) If one spring alone supported the same mass, calculate the new extension and compare the stored energy with part (c). 2

(a) Weight $=mg=117.6\,\mathrm N$. By symmetry each spring carries $58.8\,\mathrm N$.

(b) $x=58.8/1200=0.0490\,\mathrm m$.

(c) Total energy $=2[\tfrac12kx^2]=k x^2=(1200)(0.0490)^2=2.88\,\mathrm J$. Equivalently use $k_{\mathrm{eff}}=2400\,\mathrm{N\,m^{-1}}$.

(d) One spring: $x=117.6/1200=0.0980\,\mathrm m$. Energy $=\tfrac12(1200)(0.0980)^2=5.76\,\mathrm J$, twice the energy of the two-spring arrangement for the same supported load.
S8 · Mixed Topic 5 + Topic 6 challenge 10 markselastic energy
A spring of constant $450\,\mathrm{N\,m^{-1}}$ is compressed by $6.0\,\mathrm{cm}$ and releases a $0.30\,\mathrm{kg}$ trolley from rest. Take $g=9.81\,\mathrm{m\,s^{-2}}$.
compressed spring

(a) Calculate the elastic potential energy initially stored. 2

(b) If all this energy becomes kinetic energy on a horizontal track, calculate the trolley speed. 3

(c) The trolley then climbs a frictionless ramp. Calculate the maximum vertical height reached. 2

(d) In a real trial only $80\%$ of the original spring energy becomes gravitational potential energy. Calculate the new maximum height and state where the missing energy has gone. 3

(a) $E_s=\tfrac12kx^2=\tfrac12(450)(0.060)^2=0.810\,\mathrm J$.

(b) $\tfrac12mv^2=0.810$, so $v=\sqrt{2(0.810)/0.30}=2.32\,\mathrm{m\,s^{-1}}$.

(c) $mgh=0.810$, so $h=0.810/[(0.30)(9.81)]=0.275\,\mathrm m$.

(d) Useful energy $=0.80(0.810)=0.648\,\mathrm J$, so $h=0.648/[(0.30)(9.81)]=0.220\,\mathrm m$. The remainder is transferred mainly to thermal/internal energy (and possibly sound) because of resistive effects.

← Return to Topic 6 Notes