Topic 10 · D.C. Circuits
Gravity in calculations: use g = 9.81 m/s² (9.81 N/kg) near Earth, unless the question or activity supplies a different value. Keep the supplied value throughout the calculation.
10.2: both Kirchhoff laws, derivation and use of series/parallel resistance, and simple circuit analysis.
10.3: potential dividers, potentiometer comparison, galvanometer null methods, and LDR/thermistor divider circuits.
10.1 · Practical circuits
- A circuit must satisfy charge conservation at junctions and energy conservation around complete loops.
- A source’s e.m.f. is not automatically its terminal potential difference when internal resistance carries current.
- A continuous wire is one node: every point on that ideal wire is at the same potential.
- A filled dot marks a junction. Crossing lines without a junction dot are not automatically connected.
- An ammeter is placed in series and is treated as having negligible resistance.
- A voltmeter is connected across two points and is treated as having very large resistance.
- Trace the actual conducting paths before deciding which components are in series or parallel.
- Cover the labels.
- Mark the nodes.
- Ask whether current can split.
- Only then use series/parallel rules.
A diagram can look like a rectangle and still contain parallel branches. Shape is not topology.
Circuit-symbol sheet
The syllabus can use any symbol below in an examination diagram. Learn the shape, name and connection points. Recognition of a capacitor or a.c. supply symbol here does not add their later-topic physics to Topic 10.
E.m.f., p.d. and internal resistance
E.m.f. $\varepsilon$ is the energy transferred by a source from other forms to electrical energy per unit charge as it drives charge around a complete circuit:
$$\boxed{\varepsilon=\frac{W_{\text{source}}}{Q}}$$Potential difference $V$ across a component is the electrical energy transferred to other forms per unit charge in that component:
$$\boxed{V=\frac{W_{\text{component}}}{Q}}$$Both have unit $\mathrm{J\,C^{-1}}=\mathrm V$, but they describe opposite sides of the energy account: the source supplies energy; components transfer it.
| Quantity | Energy statement | Where measured |
|---|---|---|
| E.m.f. $\varepsilon$ | Energy supplied per coulomb by the source | Across an unloaded source, a high-resistance voltmeter reads approximately $\varepsilon$ |
| Terminal p.d. $V$ | Energy per coulomb available to the external circuit | Across the source terminals while it supplies current |
| Lost volts $Ir$ | Energy per coulomb transferred inside the source | Across the source's internal resistance |
Deriving the complete-circuit equation
Kirchhoff's second law says energy gained per coulomb equals energy transferred per coulomb around the loop:
$$\varepsilon=IR+Ir=I(R+r)$$The terminal p.d. is the external part:
$$\boxed{V=IR=\varepsilon-Ir}\qquad\boxed{\text{lost volts}=Ir=\varepsilon-V}$$$I\approx0$, so $Ir\approx0$ and $V\approx\varepsilon$.
$I>0$, so $V=\varepsilon-Ir<\varepsilon$.
Current enters the positive terminal, so terminal p.d. is $V=\varepsilon+Ir$.
Current can be large; do not treat $I=\varepsilon/r$ as a safe experimental instruction.
The high-value graph
- vertical intercept $=\varepsilon$
- gradient $=\Delta V/\Delta I=-r$
- use widely separated points on the best-fit line
- include the negative sign in the gradient, then report $r$ as a positive resistance
$I=\varepsilon/(R+r)=8.4/4.2=2.0\,\mathrm A$.
$V=IR=(2.0)(3.6)=7.2\,\mathrm V$.
Lost volts $=Ir=(2.0)(0.60)=1.2\,\mathrm V$. Check: $7.2+1.2=8.4\,\mathrm V$.
10.2 · Kirchhoff's laws
- Choose current directions and follow a consistent sign convention around loops.
- A negative solved current means its actual direction is opposite to your assumption.
- For a cell delivering current, terminal p.d. equals e.m.f. minus Ir.
| While tracing a loop | Term |
|---|---|
| Cross a source from short plate $(-)$ to long plate $(+)$ | $+\varepsilon$ |
| Cross a source from long plate $(+)$ to short plate $(-)$ | $-\varepsilon$ |
| Move through a resistor in the chosen current direction | $-IR$ |
| Move through a resistor opposite to the chosen current direction | $+IR$ |
Required derivation: resistors in series
The same current $I$ flows through $R_1,R_2,\ldots$. By Kirchhoff's second law:
$$V=V_1+V_2+\cdots=IR_1+IR_2+\cdots$$ For the equivalent resistor, $V=IR_{\mathrm s}$. Therefore $$IR_{\mathrm s}=I(R_1+R_2+\cdots)\quad\Rightarrow\quad\boxed{R_{\mathrm s}=R_1+R_2+\cdots}$$Required derivation: resistors in parallel
Every branch has the same p.d. $V$. By Kirchhoff's first law:
$$I=I_1+I_2+\cdots=\frac{V}{R_1}+\frac{V}{R_2}+\cdots$$ For the equivalent resistor, $I=V/R_{\mathrm p}$. Therefore $$\frac{V}{R_{\mathrm p}}=V\left(\frac1{R_1}+\frac1{R_2}+\cdots\right)\quad\Rightarrow\quad\boxed{\frac1{R_{\mathrm p}}=\frac1{R_1}+\frac1{R_2}+\cdots}$$Solving a multi-loop circuit
- Mark the nodes and choose a current arrow for every branch.
- Write one independent junction equation.
- Choose independent loops and write signed energy equations.
- Solve the simultaneous equations with units.
- Check each junction and loop; interpret any negative current.
Checks: $3.2=1.4+1.8$ at A; left loop gives $2(3.2)+4(1.4)=12\,\mathrm V$; right relation gives $4(1.4)=2+2(1.8)=5.6\,\mathrm V$.
- Do not use a resistor's current in the wrong $IR$ term.
- Do not count two loop equations that are algebraic copies of each other.
- Do not erase a negative answer: reverse the stated direction and keep the positive magnitude.
Switches and hidden short circuits
An open switch removes its branch. A closed switch with negligible resistance can join two nodes and bypass a component. Redraw the conducting circuit after each switch change before calculating.
10.3 · Potential dividers
Loaded divider
If a device of resistance $R_L$ is connected across $R_2$, the lower section becomes $R_2\parallel R_L$. Calculate that equivalent resistance first:
$$V_{\mathrm{out}}=V_{\mathrm{in}}\frac{R_2\parallel R_L}{R_1+(R_2\parallel R_L)}$$A finite load usually reduces the output compared with an ideal high-resistance voltmeter. This is ordinary series/parallel analysis, not a separate formula to memorise.
Sensor dividers: use a two-step argument
- State how the sensor resistance changes: more light lowers an LDR's resistance; higher temperature lowers an NTC thermistor's resistance.
- Identify whether the output is across the sensor or the fixed resistor, then use the fraction.
| Sensor position | Sensor resistance decreases | Sensor resistance increases |
|---|---|---|
| Output measured across the sensor | $V_{\mathrm{out}}$ decreases | $V_{\mathrm{out}}$ increases |
| Output measured across the fixed resistor | $V_{\mathrm{out}}$ increases | $V_{\mathrm{out}}$ decreases |
Potentiometer and the null method
Balance equations
For uniform wire AB of length $L$ with p.d. $V_{AB}$:
$$\boxed{k=\frac{V_{AB}}{L}}\qquad(\text{unit }\mathrm{V\,m^{-1}})$$At null, the test-cell e.m.f. equals the p.d. along balance length $l$:
$$\boxed{\varepsilon_x=kl}$$If two p.d.s are compared without changing the primary current:
$$\boxed{\frac{V_1}{V_2}=\frac{l_1}{l_2}}$$$k=2.40/1.20=2.00\,\mathrm{V\,m^{-1}}$.
$\varepsilon=kl=(2.00)(0.735)=1.47\,\mathrm V$.
| For a usable balance | Why |
|---|---|
| Uniform wire and steady primary current | Potential gradient must remain constant. |
| Correct polarity | The test e.m.f. must oppose the wire p.d. |
| Test p.d. smaller than total wire p.d. | Otherwise no balance point lies on AB. |
| Use a galvanometer | Its sensitivity reveals the zero-current condition and direction of imbalance. |
Exam toolbox
Name the energy transfer, state “per unit charge”, and distinguish source from component.
Mark nodes, label branch currents, write equations before substituting numbers.
Resistance change → measured fraction → output change. Never jump directly to “voltage rises”.
State zero galvanometer current, matching p.d.s, and no current through the test cell.
- Using $\varepsilon=V$ while a source supplies current.
- Calling Kirchhoff's first law conservation of current instead of charge.
- Adding parallel resistances directly.
- Ignoring cell polarity or an assumed current direction.
- Using the wrong resistor in the divider numerator.
- Assuming a voltmeter draws the branch current.
- Saying null means there is no current anywhere.
- Using a potentiometer as though it were only a two-terminal variable resistor.
Master Equation Sheet
| Idea | Equation | Meaning/check |
|---|---|---|
| E.m.f. | $\varepsilon=W_{\mathrm{source}}/Q$ | Energy supplied per coulomb |
| Potential difference | $V=W_{\mathrm{component}}/Q$ | Energy transferred per coulomb |
| Complete circuit | $\varepsilon=I(R+r)$ | One source, external $R$, internal $r$ |
| Terminal p.d. | $V=\varepsilon-Ir=IR$ | Source supplying current |
| Charging source | $V=\varepsilon+Ir$ | Current enters positive terminal |
| First law | $\sum I_{in}=\sum I_{out}$ | Conservation of charge |
| Second law | $\sum \varepsilon=\sum IR$ | Conservation of energy |
| Series | $R_s=R_1+R_2+\cdots$ | $R_s$ exceeds every component |
| Parallel | $1/R_p=1/R_1+1/R_2+\cdots$ | $R_p$ below smallest branch |
| Divider | $V_{out}=V_{in}\,R_2/(R_1+R_2)$ | $R_2$ lies across output nodes |
| Potential gradient | $k=V_{AB}/L$ | Uniform wire, steady current |
| Potentiometer | $V=kl$, $V_1/V_2=l_1/l_2$ | Valid at balance |