Skip to lesson
1

Topic 20 · Magnetic Fields

Gravity in calculations: use g = 9.81 m/s² (9.81 N/kg) near Earth, unless the question or activity supplies a different value. Keep the supplied value throughout the calculation.

  • Magnetic forces act on suitable moving charges and current-carrying conductors.
  • Induction is different: a changing magnetic flux linkage produces an e.m.f. Identify which cause is present before choosing an equation.
Cambridge International A Level Physics 9702

The whole topic in one idea: magnetic fields act on moving charge; a changing magnetic flux linkage produces an e.m.f. whose direction opposes the change.

Exact syllabus boundary
20.1 field concept; 20.2 force on current; 20.3 moving charge, Hall effect and velocity selection; 20.4 fields due to currents; 20.5 flux and electromagnetic induction. Current assessed Topic 20 includes electromagnetic induction. Transformer turns-ratio/power-transmission calculations and rectification/smoothing are not current Topic 20 outcomes.
A magnetic field is a field of force produced by moving charges or permanent magnets. Field lines show the direction a north magnetic pole would move.
Common mistake
Field lines are a representation of direction and relative strength; they are not material strands and are not automatically particle paths.
2

Force on a current-carrying conductor

Magnetic force directionsA current or positive charge moving right in a field into the page experiences an upward force. A negative charge experiences the opposite force.I or positive qvFnegative qvF reverses
$F=BIL\sinθ$

θ is the angle between conventional current and magnetic field. The force is zero when they are parallel and maximum at 90°.

Magnetic flux density B is the force per unit current per unit length on a wire at right angles to the field.
$1\,\mathrm T=1\,\mathrm{N\,A^{-1}\,m^{-1}}$

Fleming's left-hand rule

First finger: field (N to S). Second finger: conventional current. Thumb: force/motion. Use three mutually perpendicular directions.

Angle trap
Use the angle between I and B, not between the wire and the force. The force is perpendicular to both.
Your turn · Find force for B = 0.40 T, I = 2.0 A and perpendicular wire length 0.50 m.

Decimals, scientific notation and compatible units are accepted. Keep any required sign.

3

Force on a moving charge

$F=B|q|v\sinθ$

For a positive charge, use the conventional-current direction rule. For a negative charge, reverse the force.

Circular motion of a charge in a magnetic fieldA positive charge moving perpendicular to a uniform magnetic field follows a circle because the magnetic force is always perpendicular to its velocity and points towards the centre.××××××v tangentF inwardr = mv / (|q|B); speed and kinetic energy remain constant

Perpendicular entry

  • For a charge, F = Bqv sin θ; only the perpendicular velocity component contributes.
  • A magnetic force is perpendicular to velocity and does no work on the particle.
$B|q|v=mv^2/r\Rightarrow r=mv/(B|q|)$
$T=2πr/v=2πm/(B|q|)$

The force is always perpendicular to velocity, so it changes direction but does no work: speed and kinetic energy remain constant.

Track comparison
At the same B and v, larger momentum per unit charge gives a larger radius. Opposite charge signs curve in opposite directions.
Explain · A charge moves parallel to a uniform magnetic field. What magnetic force acts on it?

4

Hall effect & Hall probe

Hall-effect charge separationCharge carriers moving through a slab in a perpendicular magnetic field are deflected sideways until an electric force balances the magnetic force, producing Hall voltage across the slab.conventional current I××××Hall sideopposite sideV_HAt balance: E_H = v_d B; use I = n|q|wtv_d

Moving carriers are deflected sideways by magnetic force. Charge separation creates a transverse electric field until electric and magnetic forces balance.

$|q|E_H=|q|v_dB$

With slab width w and thickness t, $V_H=E_Hw$ and $I=n|q|wtv_d$. Eliminating drift speed gives

$V_H=BI/(nt|q|)$
IncreaseEffect on |VH|
B or Iincreases
n, t or |q|decreases

A Hall probe measures the component of B normal to its sensitive face. Rotating the probe varies the Hall voltage and locates the maximum orientation.

Common mistake
Use carrier-charge magnitude in the formula. Carrier sign determines Hall polarity, not the magnitude relation.
5

Crossed fields & velocity selection

Velocity selectorCrossed electric and magnetic fields exert opposite forces on a charge. Particles with speed E over B pass undeviated.××××××vmagneticelectric

Arrange electric and magnetic forces in opposite directions. For no deflection,

$|q|E=|q|vB\Rightarrow v=E/B$
Setup trap
The two fields must be perpendicular to each other and to the particle velocity, with their forces opposing.
6

Magnetic fields due to currents

Fields produced by currentsA straight wire produces concentric circles, a flat coil gives a dipole-like pattern and a long solenoid has a nearly uniform internal field.•straight wireflat coillong solenoid

Direction

Use the right-hand grip rule: thumb in conventional-current direction, curled fingers give the circular field direction. For a solenoid, curled fingers follow current and thumb points to its north pole/internal field.

A ferrous core increases the solenoid field because it becomes magnetised and reinforces the field.

Two parallel wires

  1. Current in wire 1 creates B at wire 2.
  2. Wire 2, carrying current in that B, experiences $F=B I_2L$.
  3. Same-direction currents attract; opposite-direction currents repel.
  4. Newton's third law gives equal and opposite forces.
Explanation standard
Do not write only the memorised attraction/repulsion rule. Explain field from one wire followed by force on the other.
7

Magnetic flux & flux linkage

Magnetic flux is magnetic flux density multiplied by cross-sectional area perpendicular to the field.
$Φ=BA_\perp$
Magnetic flux and angle conventionA flat coil has area vector normal to its plane. The angle theta is measured between magnetic field and the area normal, giving flux B A cosine theta.θarea normalBΦ = BA cos θ; flux linkage = NΦ

If θ is between B and the area normal, $Φ=BA\cosθ$. If an angle is instead given to the plane, use the complementary angle.

$\text{flux linkage}=NΦ$

Flux is measured in webers (Wb). Flux linkage is measured in Wb turns.

Angle check
When B is perpendicular to the coil plane, it is parallel to the area normal: θ=0 and flux is maximum. When B lies in the plane, θ=90° and flux is zero.
8

Faraday experiments & magnitude

Faraday's law: the induced e.m.f. is equal to the rate of change of magnetic flux linkage.
$ε=-d(NΦ)/dt$

How to change linkage

  • Faraday’s law concerns the rate of change of flux linkage, not simply the presence of a large field.
ChangeEffect on |emf|
faster changelarger
more turnslarger
larger area or B changelarger
constant linkagezero
Average e.m.f.
$|ε_{avg}|=|\Delta(NΦ)|/\Delta t$. Use linkage change, not final linkage alone.
9

Lenz’s law & graph transformations

Lenz's law: the induced e.m.f./current acts in a direction that opposes the change in magnetic flux producing it.
Flux linkage to induced e.m.f.A sloping flux-linkage graph produces a constant induced e.m.f. with opposite sign. A flat flux-linkage graph produces zero e.m.f.NΦεtε = −d(NΦ)/dt

Graph route

  1. Read flux linkage NΦ.
  2. Find its gradient in each interval.
  3. Reverse the sign for ε.
  4. At corners, the gradient—and therefore e.m.f.—changes abruptly.
  5. Flat linkage gives zero e.m.f.

Direction route

  1. State whether external flux is increasing or decreasing.
  2. Choose the induced field that opposes that change.
  3. Use the right-hand grip rule to obtain induced current.
Common mistake
Lenz's law opposes the change in flux. If an inward flux is decreasing, the induced field is inward to support it.
10

Paper 4 technique & master sheet

Vector–rate audit

  1. Draw v or I, B and F as a perpendicular triad.
  2. Use charge sign only after finding the positive-charge direction.
  3. For flux, mark the area normal and angle convention.
  4. For induction, calculate linkage first, then its rate of change.
  5. Use Lenz only after naming the change being opposed.

Master equations

wire force$F=BIL\sinθ$
charge force$F=B|q|v\sinθ$
circular radius$r=mv/(B|q|)$
Hall voltage$V_H=BI/(nt|q|)$
velocity selector$v=E/B$
flux$Φ=BA_\perp=BA\cosθ$
linkage$NΦ$
Faraday–Lenz$ε=-d(NΦ)/dt$
Final traps
  • θ is between I/v and B
  • negative q reverses force
  • magnetic force does no work
  • angle to area normal for flux
  • linkage includes N
  • Lenz opposes change
Boundary
Electromagnetic induction is Topic 20. Rectification/smoothing is Topic 21; transformer turns calculations are not current Topic 20 outcomes.