Gravity in calculations: use g = 9.81 m/s² (9.81 N/kg) near Earth, unless the question or activity supplies a different value. Keep the supplied value throughout the calculation.
Capacitance describes charge stored per potential difference: C = Q/V.
It depends on conductor geometry and the material between conductors.
A capacitor stores energy in its electric field, not by consuming charge.
Cambridge International A Level Physics 9702
The whole topic in one idea: capacitance measures how much separated charge is stored per unit potential difference.
Exact syllabus boundary
19.1 capacitance for isolated spheres and parallel-plate capacitors plus series/parallel combinations; 19.2 stored energy; 19.3 discharge graphs, time constant and exponential equations. Charging transients are not assessed core.
Capacitance is the ratio of the magnitude of charge on one conductor/plate to its potential (isolated sphere) or potential difference (two-plate capacitor): $C=Q/V$.
A two-plate capacitor has +Q on one plate and −Q on the other. Its net charge is zero, but charge has been separated and energy is stored in the electric field.
Common mistake
In $C=Q/V$, Q is the magnitude on one plate—not the sum 2Q and not the net charge zero.
2
Capacitors in series & parallel
In parallel, potential difference is shared and capacitances add.
In series, equal charge magnitudes occur on each capacitor while potential differences add.
Series derivation
Each capacitor has charge magnitude Q. $V=V_1+V_2=Q/C_1+Q/C_2$. Since $V=Q/C$,
$1/C=1/C_1+1/C_2$
Parallel derivation
Each capacitor has p.d. V. $Q=Q_1+Q_2=C_1V+C_2V$. Since $Q=CV$,
$C=C_1+C_2$
Connection
same quantity
adds
quick check
series
charge magnitude
potential differences
Ceq smaller than the smallest
parallel
potential difference
charges
Ceq larger than the largest
Mixed-network route
Redraw after every reduction. Mark which capacitors share the same two nodes; those are parallel. Components on one unbranched charge path are series.
3
Energy stored in a capacitor
$W=\tfrac12QV=\tfrac12CV^2=Q^2/(2C)$
The factor one half arises because V increases from zero to its final value while charge is transferred.
Known data
Best form
C and V
$W=\tfrac12CV^2$
Q and V
$W=\tfrac12QV$
Q and C
$W=Q^2/(2C)$
V–Q graph trap
The energy is the area under potential V plotted vertically against charge Q horizontally. Check the axes before using an area.
Voltage scaling
At fixed C, halving V leaves one quarter of the stored energy because $W\propto V^2$.
4
Discharging through a resistor
During discharge through a resistor, voltage and charge decrease exponentially.
Q and V have the same sign convention as chosen for the capacitor. Conventional discharge current may be negative relative to the original charging direction, so graphs often show its magnitude.
Graph fact
Meaning
initial gradient of Q–t
$dQ/dt=I$ with sign convention
area under |I|–t
charge transferred
same fractional decay
Q, V and |I| share time constant RC
never reaches zero exactly
exponential approaches zero asymptotically
Common mistake
After one time constant, 36.8% remains; it is not one half. Capacitor energy falls as $e^{-2t/RC}$ because energy depends on $V^2$.
5
Time constant & logarithm method
The time constant $τ=RC$ is the time for Q, V or |I| to fall to $1/e$ of its initial value.
$τ=RC$
Fraction-first method
Form the dimensionless fraction $x/x_0$.
Write $x/x_0=e^{-t/RC}$.
Take natural logs: $\ln(x/x_0)=-t/RC$.
Solve with R in ohms and C in farads.
$\ln x=\ln x_0-t/(RC)$
A graph of ln x against t is a straight line with gradient $-1/(RC)$.
Worked time
To reach 0.20 of the initial voltage, $t=-RC\ln0.20=1.61RC$.
Unit trap
$\mathrm{k\Omega}\times\mu\mathrm{F}=10^{-3}\,\mathrm{s}$. Convert deliberately before trusting a time constant.
6
Discharge investigation & graph interpretation
Reliable method
Charge the capacitor to a measured V₀.
Use a switch to isolate the supply and discharge through a known R.
Record V at regular times with a high-resistance voltmeter/data logger.
Repeat or use dense automatic sampling, especially near t=0.
Plot ln V against t; use the gradient to determine RC and hence C or R.
Issue
Effect
Control
meter resistance not infinite
effective discharge resistance changes
include it or use high-input-resistance logger
capacitor not fully charged
incorrect V₀
wait and verify initial reading
manual timing delay
largest effect near start
two-person method or data logger
leakage
faster non-ideal decay
clean components and compare repeats
Gradient interpretation
For ln V against t, a more negative gradient means a smaller RC and therefore a faster discharge.
7
Paper 4 technique & master sheet
Switching-sequence method
Draw the circuit in each switch position.
Use charge conservation for isolated connected conductors.
Find the new common potential difference.
Calculate initial and final stored energy separately.
Do not assume capacitor energy is conserved; resistive paths dissipate energy.
Master equations
definition
$C=Q/V$
parallel
$C=C_1+C_2+…$
series
$1/C=1/C_1+1/C_2+…$
energy
$W=\tfrac12QV=\tfrac12CV^2=Q^2/(2C)$
time constant
$τ=RC$
discharge
$x=x_0e^{-t/RC}$
linear form
$\ln x=\ln x_0-t/(RC)$
Final traps
Q is charge magnitude on one plate
series: same Q; parallel: same V
energy is triangular V–Q area
one τ leaves 1/e
energy decays twice as fast in the exponent
Boundary
Current assessed core: capacitor discharge only. Charging-transient equations/graphs, $C=εA/d$ and dielectric theory are not current Topic 19 recall outcomes.